Question about Williams-Sonoma Stick Blender Handheld

Open Question

Calcium build up causing impaired rotation

Need to disassemble shaft to clean inside

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blade on MD95 not spinning


The shaft has probably siezed at the bottom near the blade. The seal can fail and let liquid inside the shaft and gunge it up.
Take the orange handle apart, then unscrew the four steel pins, then pull out the motor. From the blade end, take the screw from the blade and prize it off. Then pull the shaft out from the top and clean it. It may be stuck - push a blunt nail or similar in the bottom to free it. Clean the shaft and solidified debris inside the tube. Then reassemble carefully.

Feb 14, 2012 | Dynamic MD95 Handheld Blender

2 Answers

Waring 34BL87 blender is loud and gives off a strong burning smell whenever used. Burning smell apparent since first day of use and getting worse with age. Is this odor normal or does it indicate the...


no, that is not normal. it could be from a loose or misallignment rotor or shafting. if its under warranty you should return it from the store...

Jun 17, 2011 | Waring TG15 Blender

1 Answer

I have a bamix M200 hand blender & the shaft does not turn although the motor is working can you help?


After a period of time food residue will migrate up through the seal on the "foot" and lodge in the shaft. Once this is gummer up the motor will go but the shaft will not be able to rotate.

The machine will need to be disassembled and the shaft cleaned out. I recommend that you find your local Bamix Service Centre to do this as there are fragile parts in the stick mixer.

May 21, 2010 | Bamix Deluxe Handheld Blender

1 Answer

Grease build up around blade and where it attaches to base


Grease can only creep into the blender vase if the oil seal has worn out, or the blenders blade shaft is worn and wobbling. Try cleaning all parts in alcohol to soften the seals. Rebuild kits and replacement blades can be found here (http://www.brevilleusa.com/breville-parts/blending.html)

Mar 09, 2010 | Breville BBL600XL. 5-Speed Blender

2 Answers

Blade doesn't spin freely


Here's the parts order form from Waring:
http://www.waringproducts.com/ret/parts/

Once you receive the parts, unscrew the collar from the bottom of the jar, and the old gasket and blade assembly will pop out - sometimes you have to peel the gasket apart from blender jar, but not always.

-Tha Mp3 Doctor

Mar 26, 2009 | Waring MX1000R Blender

2 Answers

Dynamic mx91. noisy.


dynamic mx91, motor runs but blade doesn't spin, how do i disassemble the blade & shaft?

Feb 08, 2009 | Dynamic MX91 Handheld Blender

1 Answer

25-30 year old Bamix M100 - 240V 100W


Those small plastig bungs do come out, you will need a fine probe to prise them out then you will see 2 philips head screws which hold it all together, not sure how you will tighten your shaft though, looks like it might be moulded into the plastic retainer, good luck! on mine the motor bearings are seized,
regards,
Dave Pary.

Jan 26, 2009 | Bamix Deluxe Handheld Blender

1 Answer

Older Vitamix Problem


Hi,

I want you to try this,

1.Remove the blender jar from the blender motor .

2. Check the jar by turning the shaft by hand to see if it rotates easily. .If not, disassemble the blade and ring. Check for obstructions or misalignment. It is better to change the shaft which holds the blade......

If it fails you again, you have to contact with the service center or visit this site
www.vitamix.com/household/service/service.asp

Hope my info helps you,
Thanx for using fixya,
Waiting to help you from your comments.....

Oct 01, 2008 | Vitamix Super 5000 Work Top Blender

1 Answer

Back to Basic Smoothie Freeze Bades don't rotate


check to see if you can move the blades by rotating the shaft on the bottom of the goblet, sounds like you need a new blade assembly.

you can order the part from their website:

http://www.focuselectrics.com/catalog.cfm?dest=itempg&itemid=3699&secid=53&linkon=category&linkid=91

Jun 02, 2008 | Back to Basics 600 Smoothie Plus Work Top...

2 Answers

Waring Pro MBB Blender- blade too tight


I was just able to fix mine. You'll need the following: two wrenches (almost any type), steel wool, and vegetable oil.

1. Clamp the hexagonal nut inside the bottom of the pitcher with one wrench and place the jaws of the other wrench between the "spokes" of the wheel at the outside bottom of the pitcher.
2. Turn either counter-clockwise until the hex nut comes off. At this point, you should be able to pull the bottom piece out from the bottom. Pay attention to the order and orientation of the parts inside the pitcher as they may fall out now.
3. Dry off the shaft and rub it with some ordinary steel wool (think SOS pads).
4. Twist a small amount of the steel wool and run it back and forth through the hole the shaft goes through.
5. Wipe both clean with a clean cloth or napkin.
6. Rub a little vegetable oil on the shaft.
7. Place the shaft back in the hole and test the movement. It should be like new again.
8. Reassemble the blender.

Hope this helps,

John

Mar 01, 2008 | Blenders

Not finding what you are looking for?
Williams-Sonoma Stick Blender Handheld Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Williams-Sonoma Blenders Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

eyecam

Level 2 Expert

86 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Williams-Sonoma Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...