Question about Radio Scanners

1 Answer

Channel does not go beyond channel 80 or 60 stays on those channe

I have a kenwood sirius radio in my 2003 jeep. which was installed before i I pushed a button, it said it was a menu. it now will show the artist and song being played although it is stuck on channels 60, 110, and 80. I was listening to channel 81 the 24/7 christmas music. Now I can't change the channel and the remote doesn't help. I have no idea waht to do. If you could direct me to where I could get the instructions so that I could try and fix it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

Http://audio.manualsonline.com
hope this helps..good luck!

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What steps do i take too program frequences. what are the frequences for charlotte north carolina?


with the scanner on, push the "man" (manual) button. If the scanner was scanning it should stop on one channel . Push the up or down arrow key until you get to the channel you want to program. You can also use the keyboard for direct access to a particular channel i.e. push "1" "4" "9" and "man" to jump to channel 149.

Once on the channel you want to program, push "prog" (program) then the frequency you want in that channel, including the decimal point. Push "ent"(enter). Your desired frequency should be displayed. Don't forget the "." (decimal point) or the scanner will tell you "error". Move to your next hannel to be programmed and repeat. If you put in a frequency outside of the radio's capability, you wil get an error message.

To find frequencies, look on the internet. The best site I have found is
http://www.radioreference.com/ .

Oct 27, 2009 | Radio Shack Pro-2054 Base Scanner

1 Answer

How do I unlock channels (pro-2055)


the unlock command is done from the manual mode.

If you scanner is in the scan mode, push the "MANUAL"button to stop the scanning feature.

Next you need to go to the channel you want to unlock. If you are only a few channels away, while in the manual mode, push the up or down arrows to step (one push per channel to be stepped though) to the channel to be unlocked.

A direct method is to enter the channel number on the keypad and then push the "manual" button. The display should show the channel you desire.

If the channel lockout is on, the second line on the display will show "LO+". Push the keypad button marked "L/OUT" once. The "LO+" should change on the display from uppercase to a lowercase "lo+". The channel is now unlocked.

Oct 16, 2009 | Radio Shack Pro-2055 Base Scanner

5 Answers

Cannot unlock Uniden BC60XLT-1 (30 ch VERSION)


if all the channels are 000.000 then it wont scann youll have to hit manual then enter a freq then hit the "e" button. once you hit manual youll be able to push the up and down arrows to select an channel you wish to imput a feq. Hope this helps.
David

Jun 29, 2009 | Uniden BC60XLT Handheld Scanner

1 Answer

Pro 95 dual trunk tracking scanner just stays on channel 3 does not scan up to the other 10 channels


the manual at "http://support.radioshack.com/manuals/ome20-525.pdf" (if you don't have it)
says that you may be in manual mode OR that the channel at 3 might be a "trunk guide", that means that the channel is used to send out digital permissions to the system for each radio in the unit(s) to use a certain freq. when they transmit. good luck!

Mar 04, 2009 | Radio Shack Pro-95 Handheld Scanner

1 Answer

Acts like squelch is stuck


I had the same problem. Your board may be fried. I had to buy a new unit.

Jan 28, 2009 | Uniden BC248CLT Base Scanner

2 Answers

Unlocking channels


first press the manual button so you can go through the channels one by one. Then look for a button that has L/O(lock out) push this once for every channel you have a frequency programmed for it, the channel will probably not unlock if there is no frequecy programmed to it.

per roupe50 above

Dec 25, 2008 | Radio Shack Pro-95 Handheld Scanner

1 Answer

Scanning programmed channels


Not exactly. You can program channels however into the Private bank. To do so though you must search for the channel first...This may simply mean going to a channel you already know by using the band button to start searching...Push the hold button to stop it close to the frequency and then use the arrow keys to get to the exact frequency. then push the Prog button. After pushing it, push the Private button (you will see CH next to the frequency) using the arrow keys select the channel you want to store on and push Prog again. To scan the stored channels simply push the private button...Done! It can be a tedious process...expecially with 50 channels....but It's the only way I know how to do it...Good luck!

May 11, 2008 | Uniden BC350C Base Scanner

4 Answers

Programming Bearcat BC 55XLT Scanner


Ok doc, I'll see if I can walk you thru this as there don't seem to be a manual available for download.
* Push manual button and bring it around to channel #1
Enter the freq including the decimal point. Push the E button to enter the freq into the first channel.
* Push manual again and move to channel #2 and repeat.
If you need some new freq's for your area, go here, click on your state, county, and it'll give you a complete rundown.
http://www.radioreference.com/apps/db/

If you need 10 codes for your area, go here and click on your state.
http://www.nat-com.org/radio.htm
If you need anything else, let us know,, Mechanic

Feb 19, 2008 | Radio Scanners

3 Answers

Radio Shack Pro-95 handheld scanner issues


Here is the online programming tutorial:
http://support.radioshack.com/support_tutorials/communications/200-0523/67345.htm

Here is the full manual Should include Quick guide:
http://support.radioshack.com/manuals/ome20-525.pdf

Here is FREE programming software for the PC:
Includes hardware info. You can buy programming cable at Radio Shack to connect to your PC.
http://www.starrsoft.com/freeware/win95/default.asp

Jan 02, 2008 | Radio Shack Pro-95 Handheld Scanner

Not finding what you are looking for?
Radio Scanners Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Scanners Experts

Iron
Iron

Level 3 Expert

3018 Answers

Robert McClure

Level 2 Expert

160 Answers

John
John

Level 2 Expert

473 Answers

Are you a Radio Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...