Question about Frigidaire Affinity ATF7000E Front Load Washer

1 Answer

Final Spin Cycle gets stuck at 1 minute

Our machine gets stuck at the 1 minute mark. It is in its final spin but doesn't actually time itself out. It appears to happen with larger/heavier loads. In addition to the sound of a 747 landing in the house

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Back tub bearing,,and spin surport,,defective,,,under warranty,,,call for service..onthejob

Posted on Feb 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer stops during normal wash cycle for a minute or more, and then continues. Would replacing the timer fix it?


If it actually goes on and finishes the cycle and that really bothers you replace it. If not leave it alone and allow a little more time to complete its cycle. The lid switch only keeps the spin cycle from going with the top open.

May 23, 2014 | Whirlpool Washing Machines

1 Answer

STYLEMATER 4214164, AGITATOR SEAMS TO BE STUCK,


are you sure it's aggitating?common problem with direct drive washers is the motor coupling breaks and the transmission can't engage with the motor or you could have a bad transmission.usually you'll find oil leaking out of the ******. you can check this and the coupling at the same time.one other thing,when in spin open the lid and then close it and listen for a clunk and see if it spins,that would be the clutch on the ******.if this happens see if you can get it to spin in any other cycles,i've had bad timers do this,if it spins near rinse but not in the final spin and if you open the lid,close the lid and then the clutch falls and it does spin i'd say you have a bad timer,you can watch the timer,if it moves all the way to end but it doesn't spin in the same spot on the final spin but does spin in any other cycle it's the timer.but check the coupling first.http://www.youtube.com/watch?v=9K1KHEogf3c copy and paste,it will show you how to get at the coupling.

Oct 30, 2011 | Roper RAS8445KQ Top Load Washer

1 Answer

Kenmore 70 Series Washer Won't advance in the


Bad timer. Try to find a used one if possible, this item is a little expensive.

Aug 23, 2010 | Kenmore Washing Machines

1 Answer

LOUD CLATTERING NOISE DURING LAST MINUTE OF FINAL SPIN CYCLE


the loud clattering noise you hear is the main bearing it needs replaced.the main reason for the repair men doing a runner is its not an easy job and takes time and know how.if i was you i would get some estimates on this job,i would guess they will be high because no one wants to do it.Would you not consider a new machine???????anyway good luck.adrian,,,,

Jul 09, 2010 | GE Profile WPRE6100G Top Load Washer

1 Answer

It gets through to the 40 minute part of a cycle and shuts off and unlockes door and has ol code


This kind of problem is usually when the final spin is overloaded and the overload sensor stops the spinning. But, this can also happen during the spinning at end of wash cycle. Does this shut-down occur every time? If not, then it is your load that is too much. If it happens every time, then it is most likely the overload sensor. The electronic timer could be the problem (they are more flukey than the mechanical timers) but usually you will not see OL if the timer itself is at fault. Good luck, Macgivor.

Dec 27, 2009 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

Will not go into high speed final spin after rince cycle..only spins back and forth slowly and the uE indicator comes on stopping the machine. Have tried taking out a few laundry items and re-starting and...


uE is unbalanced error. When you have bulky items, wash them with a slow spin speed. Larger loads actually balance out better, so adding items might help instead of subtracting them. After the cycle completes, if you want to you can turn the power on again and (without selecting a cycle) just push the spin speed selector button and select the next highest spin speed. The load will most likely make it through the next higher speed now that it is partially spun out. You should get a 14 minute spin and pump only when you start it now.

Nov 15, 2009 | LG WM0642H Front Load

1 Answer

Maytag neptuneMAH9700 front load washer


Another computer generated flaw.The worst thing is alot of times that "flaw" can be a costly one                       

May 04, 2008 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Frigidaire Affinity ATF7000E Front Load Washer Logo

863 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...