Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

1 Answer

Whirlpool ultimate care II quietwash filling with water during spin cycle

My Whirlpool Ultimate Care II Quietwash washer fills with water during the spin cycle. This happened a few years ago and I replaced the inlet valve. I tried doing this again and the washer worked for several loads before doing the same thing. Is there any other part I should try to replace or is this just a defective inlet valve. Any ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Whirlpool Master
  • 713 Answers

Sounds like the valve again

Posted on Oct 26, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mikedurland
  • 481 Answers

SOURCE: Whirlpool Ultimate Care II Plus Washer Model: LSQ9264HZ0

if you hear the motor running while it is supposed to be agitating or spinning then it is most likely the direct drive coupling between the motor and transmission.43f18ab.jpg9bd1c44.jpg if you already checked this and think it is a different problem then let me know, i will help you figure it out.  Mike  

Posted on Jul 15, 2008

Maytag317
  • 1136 Answers

SOURCE: Whirlpool washer ultimate care II sometimes does not spin.

HI It sounds like the spin basket drive is going bad. If it was the lid switch, you would get no sound. Let me know if I can assist you further.

Thanks
Vic

Posted on May 16, 2009

  • 136 Answers

SOURCE: does not spin or empty

it might be jammed or there might be dirt or some sort of a clog. I would suggest you clean it out.

Posted on May 29, 2009

honeymokey
  • 3113 Answers

SOURCE: Whirlpool Ultimate Care II washer fills with water and stops

Lid switch. Push down on lid.

Posted on Jun 18, 2009

SOURCE: whirlpool ultimate care II stops after filling

Hi, could be faulty timer, faulty water level switch, faulty start capacitor for motor, or faulty motor. always put clothes in machine before starting. you can empty machine by lowering drain hose to flow level.

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stops in the middle of wash cycle


Hi!

If the cycle doesn't advance, it's probably the timer or a cold-water supply problem:
It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.
It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Please do rate this solution as FixYa and revert for further assistance.

Thanks
Rylee

May 29, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II keeps taking water.


ck your drain nose/drainline, chances are you have along hose, perhaps even draining along the floor behind hte unit, into a "closed" drain system. in which cawee the wwater is syphoning out during the rinse cycle, youlll needt o raise the drain hose to above 48" and have it drain into a stand pipe to prevent siphoning effect

Nov 19, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II


sounds like a broken coupling.
it probably don't agitate either.

Oct 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Washer will not Spin during SPIN CYCLES


Thanks for the question If your washer sorta spins and washes ok, your problem is with the transmissionTHanks for your question THe Appliance doc

Jul 29, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool ultimate care II stops during cycle


THe most likely cause for this is either the lid switch or the timer itself sticking.

Sep 14, 2007 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...