Question about Audio & Video Receivers

1 Answer

Getting Back Speakers for Onkyo tx 500 to work

My front speakers work for my surround sound, but the back ones will not produce any sound. One person I found said all that was needed was to adjust the number of speakers, but either I was pressing the wrong buttons, or it didn't work. Anyone have any idea? Thank you.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had to turn my speaker B off in order to set up my 5 speaker system. Thanks for getting back to me though. I really appreciate it.

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Onkyo tx ds777 model and I can only get sound to come out of the front speakers on direct mode. Stereo or any type of surround sound produces no sound at all. I have tried with my mp3 player...


You don't say if all speakers work with the setup procedure. THAT is step 1. Then try FM as it doesn't require any cabling. Then move on to more complex sources like external analog, then digital (and make sure to assign the ports).

Aug 22, 2011 | Onkyo TX-DS777

1 Answer

ONKYO TX-SR701 - Hi When using the speaker config I can get output from all speakers but the Surround back speaker R does not work. I do get sound from Surround back L. It's a bit confusing as the...


Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Onkyo-TX-SR701-Receivers-manual/id/365ag222/t/2/

7.1 would have Surround Back L and R.

6.1 would have just one back there (SB). It defaults to the Left output on the Pre-Outs if you ever go that route.

This being a 6.1 receiver it does not support two SB channels BUT you can configure those amp channels for a separate Zone supporting 2 speakers. Confused?

The manual shows a single SB speaker connected to the left side on Page 27. THAT would be consistent with a 6.1 configuration.

Jun 04, 2011 | Onkyo TX-SR701 Receiver

1 Answer

I have just bought a new Onkyo TX-NR808 and set it up over the week end with new 'accusound' surround sound speakers. Have bi-amp the front speakers. I don't think I am getting very good sound out of it?...


Depending on the amplifier, it might not provide enough power (in Watts) to the speakers. If the speakers require more power, it won't be as loud.

Mar 06, 2011 | Onkyo TX-8222 Receiver

1 Answer

Garbled / feedback sounds from powered subwoofer


The surround processing portion of the unit has a problem. In either stereo or direct mode, the digital procesing is bypassed. This could be just the surround processing IC, but that IC may not be available as a separate part. I would suggest that you bring this unit to an authorized Onkyo service center for an estimate.

Dan

Mar 18, 2009 | Onkyo TX-DS595 Receiver

1 Answer

My Onkyo TX SV 535 Surround Sound wont work


when the stereo or mono listening mode is selected only front speaker and subwoofer produce sound--------make sure that speakers are configured correctly.
and you select surround sound in listening mode.

Aug 17, 2008 | Onkyo TX-SV535 Receiver

1 Answer

I have an onkyo tx-sr606 with speakers set up at 5-1 channel, when trying to set up the auto speaker set up i keep getting the speaker detect error message. what can i do ?


hi there. try to check if your surround speakers are on the surround terminal. do not put them on the surround back terminal because this is only allotted for the 7.1 speakers. hope this helps.. ^_^

Aug 12, 2008 | Onkyo TX-SR606 Receiver

1 Answer

Righ & Left Front speakers not functioning


SOUNDS LIKE HE HIT YOUR SPEAKER CHANELS 1 OR 2,,, PUSH 1

Mar 15, 2008 | Onkyo TX-SV545 Receiver

1 Answer

Onkyo TX-SR500 Dolby Digital problem


I just read over the problem you were having with your Onkyo TX-SR500 receiver. It sound like the unit needs to be setup for all five channels.Sence your symptom says the diplay shows Dolby D3/2.1. According to the owners manual with the remote control look for speaker setup whin the button is pressed the current speaker setup will be shown in the display. Press the preset/adjustment<> to change the current setting to five speakers. the listening mode will automatically change according to the number of channels you selected. Hope this helps. Radiotech

Aug 14, 2007 | Onkyo TX-SR500 Receiver

1 Answer

NO surround sound coming from our harmon/kardon speakers when set up to our onkyo tx-sr601 receiver. wires connected in correct areas, front left, right and center speakers work, subwoofer works. setup for...


So your saying that you have no rear channel. Some recivers use a single stereo output ic for both sides on the rear speakers. you could have a defect with this IC . Anther thing Im sure you check3ed the obvious ie : the switch is on suround sound? If there is a front to rear fader is it in the middle? Good Luck

Jun 04, 2006 | Onkyo TX-SR601 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68250 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...