Question about Microsoft Broadband Networking MN-100 Wired Base Station (M51-00001) Router

2 Answers

New pc.. old router. not detecting internet

I recently switched to vista and now my 100 year old Microsoft router (Wired Base Station MN-100) wont detect my internet connection.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I'm using the MN-100 router right now and it works perfect with Vista! with DSL PHONE LINE
log into your base station(MN-100) defualt password is: admin
1. Make sure 'DHCP server' is set to 'Enabled'.
2. 'Network Mode' setting must be set to 'Routing mode'.
3. Works with Firewall enabled.
GO TO the page (Wide Area Network (WAN) Settings
enable: PPPoe-uses point to point protocal over ethernet
then below that enter user name & password same as you did the first time you used your DSL i include (MY)service name too(SBC Global) when done go back to home page click connect may take a min or two your done! after initial setup is done its fast and you dont have to put user name or pass in again either!

Posted on Feb 22, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,061 Answers

YOUR ROUTER IS NOT COMPATIBLE WITH VISTA NO WORK AROUND OR FIRMWARE UPDATE WILL WORK.REPLACE.RICHARDM69

Posted on Dec 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Install software for vista premium for my mn-100 router


router do not require software unless this is a usb version.

Jun 07, 2008 | Microsoft Broadband Networking MN-100...

1 Answer

AFTER USING THE MN-100 BASE STATION FOR FIVE YEARS, IT ISN'T GETTING ANY POWER (LIGHTS NOT COMING ON) YET THE PLUG HAS JUICE. DO THESE JUST WEAR OUT OVER TIME?


All electronic devices will eventually fail, depending on how well they are manufactured and the conditions they are operated under.
Things that will lower the lifespan of a router : high sustained amounts of traffic, being crammed into a tight space where they do not have room to remain cool, poor power, spikes or brownouts can be very damaging to routers. I would suggest making sure it is plugged into a proper surge protector in a well ventilated area.
That said, 5 years is a decent lifespan for such a device, most manufacturers will only warranty such devices for 1 year.
hope this was helpful.

May 30, 2011 | Microsoft Broadband Networking MN-100...

1 Answer

Router doesn't work since moving.


That is a question for you to pose to your new service provider.

Sep 09, 2017 | Microsoft Broadband Networking MN-100...

1 Answer

MN-700 needs constant re-setting


probably overheating u may need to get a new one. :(

May 24, 2009 | Microsoft Broadband Networking MN-700...

2 Answers

Reconnecting Wired Base Station MN-100


Yes, that is possible. Since you have changed providers, you have to reconfigure the router depending on your new provider.

You can try these steps:

1. Turn off the the router, modem and the computer.
2. Wait for 30 seconds then turn on the modem and make sure that all (if not most) lights are stabilize
3. When the lights are stabilized, turn on the router and wait for the lights to stabilize.
4. When both the router and the modem are stabilized, you can turn on the computer and check for the connection.

If it still does not work, you may need to configure the router based on the settings needed by the service provider that you have. If you wish, inform me of the name of your service provider and I will give you the specific settings on how to configure your router.

Sep 17, 2008 | Microsoft Broadband Networking MN-100...

1 Answer

Wired router connection


Sorry, routers are not my area of expertise. Please try a different expert..Benimur if possible. He's good with this stuff.. or even Ekse.

May 16, 2008 | Microsoft Broadband Networking MN-100...

1 Answer

Connection Issues Occur When I Try to Connect Through a Broadband Network Adapter


To resolve this issue, remove the network bridge. To do so, follow these steps: 1. Click Start, and then click My Network Places. 2. In the left pane, click View Network Connections. 3. Look for any connection that is bridged. 4. Right-click the bridged connection, and then click Remove From Bridge. 5. Repeat step 4 for each connection that is connected with a bridge. 6. When the bridge is removed from each network adapter, right-click Network Bridge, and then click Delete. 7. Click OK. When the all the bridged connections and the network bridge are removed, the broadband hardware is automatically detected.

Feb 16, 2006 | Microsoft Broadband Networking MN-100...

Not finding what you are looking for?

Open Questions:

Microsoft Broadband Networking MN-100 Wired Base Station (M51-00001) Router Logo

Related Topics:

362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Computers & Internet Experts

micky dee

Level 3 Expert

3000 Answers

Piyal Perera
Piyal Perera

Level 3 Expert

528 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Are you a Microsoft Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...