Question about Tricity Bendix 24 in. DH102 Free-standing Dishwasher

1 Answer

Tricity bendix dh101 wont empty trying to but only a trickle was working ok no kinks in extract pipe

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Tricity Bendix Master
  • 19,396 Answers

Check the drain hose and the drain lines, if you find no obstructions, then you have a defective drain pump.

If you find no problem with the drain lines, you may need to replace the pump.

If you enter model number here , you can find parts and diagrams.

Posted on Dec 08, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My tricity Bendix dh101 fills with water goes for a short while and the trips the electricity. This is concerning me.

Most likely..... 1st does it run the exact amount of time when it trip. If so the action that it is about to cycle into has to much of a load on it, or bad breaker. if machine detects a problem it will automatically go 2 zero and let the water out. Also check the board for corrosion

Dec 19, 2017 | Tricity Bendix Washing Machines

1 Answer

I have a tricity bendix dh101 stopped working cold water not going in to manchaine many thanks if u can help

Possible that the INLET valve is faulty /clogged or there is no voltage to switch ON the inlet valve.
So measure the voltage at the inlet valve, also check if the inlet filter is clogged.
Check the water pressure at the inlet to confirm, remove the line from the inlet valve and confirm the flow when activated.

Aug 08, 2011 | Tricity Bendix Dishwashers

1 Answer

I have a Tricity DH101 replacement element, but can't see how I remove the old and replace it with the new one, do I have to do this from beneath the unit?

No. You need to remove the perforated floor of the machine to access the heater element, and you need to remove the rear cover to disconnect the wires. Once you have access to these points the job is actually very easy. Make sure that the power cord is removed from the wall socket before attempting any work on the machine.

Jun 25, 2011 | Tricity Bendix Dishwashers

1 Answer

I have a tricity bendix dishwasher and it is not draining fully at the end of the cycle? If I run the dishwasher into a bucket the water pours out nice n strong. The waste pipe is not blocked, and I have...

Check the fitting where the dishwasher hose connects to the drain. If it drains when disconnected, it is either kinking the hose when you put it back in, or the drain is plugged at the connection.

Nov 19, 2017 | Tricity Bendix 18 in. DH090 Free-standing...

1 Answer

Iv got a Bendix BIW103W, water runs to machine from mains, no blockages, but only trickles into dispencer, doesnt take powder or fab softner into drum, otherwise works ok,

i would check the water inlet on machine............take the hose off there should be a small filter inside. might be blocked..................

Mar 31, 2011 | Tricity Bendix AW1000W Front Load Washer

1 Answer

It won't go into the spin cycle

Have you checked that the filter at the bottom r/h of the machine is clear and that the pump turns freely if that is ok make sure that the drain pipe is not blocked or kinked.If you are still having problems then it could be the motor,brushes or belt.
Good luck.

Apr 25, 2010 | Tricity Bendix AW1000W Front Load Washer

1 Answer

Tricity bendix dh101

Check pressure from power supply, check if the inlet valve is faulty or obsstructed.

If you enter model number here , you can find parts and diagrams.

Nov 03, 2008 | Tricity Bendix 24 in. DH102 Free-standing...

1 Answer

Wont spin

the pressure switch tube will require a blow through,thats if the pumps ok and clean.or a freak happening would be a blocked waste pipe( i have seen this before after much head scratching!)

Aug 27, 2008 | Tricity Bendix AW1400W Front Load Washer

2 Answers

Tricity Bendix DH101 dishwasher

my tricity bendix dh101 will not fill up with water what could be the problem

May 09, 2008 | Tricity Bendix 24 in. DH102 Free-standing...

Not finding what you are looking for?
Tricity Bendix 24 in. DH102 Free-standing Dishwasher Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tricity Bendix Dishwashers Experts


Level 3 Expert

102366 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Kevin Getz
Kevin Getz

Level 3 Expert

1031 Answers

Are you a Tricity Bendix Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides