Question about Kenwood VR-7080 Receiver

2 Answers

No sound out of receiver

I am unable to get sound out of my kenwood vr7080 receiver. I have all the speakers wired up correctly and do not have it on mute. I have it connected to the right zone and I have turned to volume all the way up and down. I have reset the receiver per instruction manual and still nothing is heard. I have gone through all connected components that are on like dvd, video1, video2, video3 with no sound.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I make sure the a botton and b button was press and still no sound what else can it be

Posted on Mar 06, 2015

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Check to see if Speaker A (Under the Power Button) is pressed, if Speaker A is selected, the icon will illuminate in the Display panel. Try Speaker B if this should not be the case. Generally, the Speaker A setting will supply power to all connections from the internal amplifier. Speaker B will supply frequency signals to a preamp or minimal power to an aux. room.

Posted on Feb 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speaker connection are correct but there is no sounds


Check your connections. Some cars have a factory amp. You need to connect the so,I'd blue wire with white stripe. Also connect the solid blue to those wires

Apr 30, 2016 | Kenwood Car Audio & Video

1 Answer

I want to connect kenwood woofer sw-07 to pioneer amplifier vsx-d859tx. i am unable to connect please guide me.


Hello,

I don't recall correctly if your Pioneer has a sub out RCA connector, and if the Kenwood SW-07 has a low level input. So the usual way is to connect it using the speaker wires.
You connect either the FL or the FR to the sub and it should work.

Good luck

Jan 11, 2015 | Pioneer Audio Players & Recorders

1 Answer

Kenwwod KDC MP 543u Protect mode problem


This indicates a short in one of the speakers, or possibly the speakers are not wired correctly. Please see my tip at http://www.fixya.com/support/r9389300-stereo_says_protect_or_clicks_off_when .
Correct wiring for 95 Corolla is as follows:

1995 Toyota Corolla Wiring harness, Kenwood wire color
Radio Constant 12V+ Wire: Blue/Yellow, yellow
Radio Switched 12V+ Wire: Gray, red
Radio Ground Wire: Brown, black
Radio Illumination Wire: Green, not used by Kenwood--please tape off
Radio Antenna Trigger Wire: Black/Red, blue
Left Front Speaker Wire (+): Pink, white
Left Front Speaker Wire (-): Purple, white/black
Right Front Speaker Wire (+): Light Green, gray
Right Front Speaker Wire (-): Blue, gray/black
Left Rear Speaker Wire (+): Black, green
Left Rear Speaker Wire (-): Yellow, green/black
Right Rear Speaker Wire (+): Red, purple
Right Rear Speaker Wire (-): White , purple/black

Dec 29, 2011 | Kenwood Car Audio & Video

1 Answer

No sound from speakers


check to make sure you have your speakers turned "ON" many amps have "A" and "B" speakers or 1 and 2 and then check the back to make sure no wires are touching and determine what output you are using for your speakers.... also you have to make sure that that corresponding button is depressed for those speakers.... also check you have the correct input selceted for your speakers and that no wires are crossed..... theres is probably notihng wrong with the speakers you just need to paly with your amp

Jun 18, 2009 | Kenwood Audio Players & Recorders

1 Answer

No sound from speakers


Check the audio settings in your Kenwood consult the manual.

May 08, 2009 | Car Audio & Video

1 Answer

Kenwood VR-305 receiver surround speakers will not work


make sure that all input cables are in the correct positon also make sure that any inputs you are using don't have a macrovision in them that will also kill your sound due to copyright laws and stuff but main thing check all wires coming in to receiver and if you need more inputs go to walmart and get a rca splitter basicaly its a 1 in two out connection to add more cables in the input

Mar 16, 2009 | Kenwood VR-305

1 Answer

No sound


it sounds like you have a short on two of your speaker wires just connecy front speakers and try then rear then left then right to prove which one or ones 
chris

Oct 29, 2007 | Kenwood KDC-217 CD Player

Not finding what you are looking for?
Kenwood VR-7080 Receiver Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

Eddie Dalton
Eddie Dalton

Level 1 Expert

41 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Kenwood Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...