Question about Sharp XR-11XC Multimedia Projector

1 Answer

No power indications

My projector shut down while watching it. No previous warning signs. now i am unable to power it back up. Not even a standby light. Is there a replacable fuse or something inside?

Posted by on

  • 4 more comments 
  • greenup Dec 19, 2007

    After unpacking from a move, I couldn't get it to power up. Changed power cords, tried using the remote to power up, Nothing. Not so much as an LED.

  • man4pnw Jun 27, 2008

    Sharp XR-11XC projector unexspectedly shut down. No power, no indicator lights, nothing. Changed lamp, changed power cord, tried plugging power cord into other electrical outlets in the home. Nothing Nada.



    Can somebody through me a clue? Is there an internal fuse?

  • mthayne Jul 08, 2008

    I was just watching a movie on my XR-11XC Sharp Projector when it powered down without warnings or indicator lights. The bulb still had about 60% life last time I checked. Now I can't get it to come alive. No lights, no noises, nothing. Is there a reset or?????? Help

  • spoonface Jul 27, 2008

    I experienced the same behavior while using my projector last night. It turned off while I was watching, tried plugging into different outlet, no power indicators, etc. Extremely bummed about this. I figure either there's a fuse or the power supply is blown. Looking for a service manual.

  • Anonymous Sep 20, 2008

    After an unexpected shutdown during a movie, the unit does not power up. I changed the bulb, but it still does not turn on. No indicator lights are lit, no fans running. It is completly dead.

  • Anonymous Mar 31, 2009

    right on - thanks much - this fixed the problem........

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Remove the six screws from the bottom and 2 screws in the back that hold on the top cover. Once you have the top cover removed you will see a small round red button on the front of the unit. Press this button in; it should not pop back out. Put cover back on and plug it in.

Posted on Dec 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Warning and standby indicator of JVC D-ILA Projector model DLA-X70RBE flashing simultaneously.


Johan, Below are links to your model where you can access,manual,instructions and get support.
Press the helpful button and follow me on fixya for more tips and info.

4K shift ILA Projector DLA X70R Introduction

Replacing lamp on JVC Series Projectors



JVC DLA X3 Warning light issues

Feb 11, 2016 | JVC Televison & Video

5 Answers

No power indications


Greetings,

Fuse problem or power supply.
If it's the lamp, you'll still get a standby light.
Check also the ventilation, that might caused it to shutdown.

Keep us posted and thank you for using our service.
FixYa for all your troubleshooting needs.

Jul 09, 2008 | Sharp XR-11XC Multimedia Projector

1 Answer

Sanyo plv z2000 warning led it shutdown


Check all the fans if its working or avoid anything that cover the exhaust fan, or the temperature of your room.

Oct 23, 2009 | Sanyo PLV-Z2000 Projector

1 Answer

My xg-e650ub also shut down while in use, and won't power up.


Reset the lamp timer.
1,Connect the power cord.
2,While simultaneously holding down "menu","enter" and "down" on the projector, press "standby/On" on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.
"LAMP 0000H" is displayed, indicating that the lamp timer is reset.

Jul 24, 2009 | Sharp PROJECTOR LAMP, Projector Lamp FOR...

1 Answer

EIKI XB23 PROJECTOR WON'T GO ON


Do you hear the fan start up? or does the projector lamp come on (you start to see an image)?

If yes to either:

When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down
to protect the inside of the projector. The POWER indicator
is blinking while the projector is being cooled down. When
the projector has cooled down sufficiently (to its normal
operating temperature), it can be turned on again by
pressing the POWER ON-OFF button.

Note:
After the temperature inside the projector returns to normal, the
WARNING indicator still continues to blink. When the projector is
turned on again, the WARNING indicator stops blinking.

Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if
ventilation slots are not blocked.
– Is the projector not installed near the ventilation duct of
air-conditioning equipment which may be hot? Install the
projector away from the ventilation duct of airconditioning
equipment.
– Are the air filters clean? Clean the air filters periodically. Let me know if you need to know how to do this.

If no to either:

When the projector detects an abnormal condition, it is
automatically shut down to protect the inside and the
WARNING indicator will be red. In this case, disconnect the
AC power cord and reconnect it, and then turn the projector
on once again for check. If the projector cannot be turned
on and the WARNING indicator emits a red light, disconnect
the AC power cord and contact the service station for check
and repair.

Please let me know if this helped solve the problem. If not, is there anything else you observed - whether or not you believe it's relevant.
1ak+f4pj7cbm32cuniyi2gaaaaaelftksuqmcc

Jun 26, 2009 | Optoma EP716 Multimedia Projector

1 Answer

The clean your filter warning sign comes up and then shuts the projector down in 1 min. I have changed the lamp and filter. How do i reset the timer for the Lamp Hours and get rid of the warning?


Once the filter is replaced, plug the projector back in and make sure the projector is in standby mode.  Point the remote control at the projector and press the following buttons in order in less than 3 seconds: reset, ←, →, enter.  This worked for me.  Good luck.

Feb 21, 2009 | Sony VPL-VW100 (Ruby) Multimedia Projector

1 Answer

NEC LT240 has Power, Status & Lamp indicators lit & wont turn on!


If your bulb finally reaches it's end before you have the chance to replace it you unit will shut itself down and go into a permanent standby mode. Changing the bulb alone will not remedy the issue. The solution is quite simple but not posted in the manual or anywhere else that I could find for that matter! All that is required is to hold down the HELP button on your remote for 10 seconds while aiming at the infrared sensor on the unit. This will reset the units bulb timer and remove it from the standby mode.

Dec 10, 2008 | NEC LT 240K Multimedia Projector

2 Answers

Infocus IN72 Projector. NO POWER OR NOT POWERING UP


This model projector is very sensitive to internal heat. I f by some reason the projector was abruptly powered down without the use of its normal procedure, in other words, unpluging cord from wall while on or power outage in premises, then the heat remains trapped and the sensors overheat and subsequently shuts down the unit. Now, although, once the sensors cool down it should reinstate operation some sensors become permanently damaged due to the extreme heat. In this case without having more facts, i believe it is the cause. I recommend a free check up to your nearest shop, most shops will offer free check ups.

Jun 07, 2008 | InFocus IN72 Multimedia Projector

1 Answer

My Panny AE700U shut down & won't restart


HI there

This is a faulty Mainboard that will need either repair or replacement.

If a Projector starts playing on and off tricks I have found it to be 99% of the time a faulty Mainboard.

Apr 13, 2008 | Panasonic PT-AE700U Multimedia Projector

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

257 Answers

k24674

Level 3 Expert

8073 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...