Ht-x250 no volume - Samsung HT-X250 Theater System

Hi JOHN MATHEW
1.Your Samsung HT-X200, has power supply problems and problems with audio output
2. To convert your Samsung HT-X200 (2.1) to an HT-X250 (5.1), you must add a DSP, several amplifier stages, one for each channel added
You will find it cheaper to replace your Samsung HT-X200 (2.1) with a Samsung
HT-X250 (5.1)
Hola JOHN MATHEW
1.Tu Samsung HT-X200, tiene problemas de fuente de alimentacion y o problemas en la salida de audio
2. Para convertir tu Samsung HT-X200(2.1) a un HT-X250(5.1), deberas agregarle un DSP, varias etapas amplificadoras, una por cada canal agregado
Te va a resultar mas economico reemplazar tu Samsung HT-X200(2.1) por un Samsung
HT-X250(5.1)

https://elektrotanya.com/samsung_ht-x200_ht-x250.pdf/download.html

The mike can be a mismatch with your CB A booster mike amplifier with a volume control will suffice.

Generally speaking, an amp attempts to protect itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'nekkid'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Check for loose speaker connections at the speaker as another possible root cause for intermittent shutdown.

did you sort this out?

buy a new one you ********

Hello, please get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay_cvb89i

Using trial and error, I set the time on my JVC PC-X250 boom box by:

1. Turn unit OFF.
2. Press and hold PROG/SET button until hour digits start flashing.
3. Use SEARCH DOWN and/or UP buttons to set correct hour (including AM/PM).
4. Press PROG/SET again until minutes digits start flashing.
5. Use SEARCH DOWN and/or UP buttons to set correct minutes.
6. Press PROG/SET again until time is not flashing.

o2bad455

with the receiver power off, hold down the stop button on the front of the receiver for 5 seconds. it will reset the system.

I'm afraid that's teh case with your unit. PROTECTION error actually means the unit is overheating and it shuts itself off to avoid further damage. Just make sure that there are no other device below the unit and that there is adequate ventilation at the back.

If all else fails, the unit's fan is definitely defective.

Had this same issue with my Samsung HT-X50, it seems these systems have cheap fans. Mine was under warranty but when I contacted samsung they wanted me to pay to ship it to them. **** that, it would of cost me 70 to ship.

What I did was open the unit take the fan and go to a computer store asking for a similar one, I got all this done for about 10 bucks. **** that samsung warranty