Question about Intel D845GVSR Motherboard

1 Answer

What is computer bios checkcum error & bios could not opend

Hi pls help me

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 201 Answers

Note: This error is not the same as a CMOS Checksum Error, which refers to corrupted values of the CMOS settings, the ones you set through the BIOS setup ... When computer on tap the del buuton to get in your bios, some mainboards use F2 key when in the bios set bios defaults this should work, unless you changed hardware inside your computer

Posted on Dec 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi am NEL.. i have MSI PM8PM-V mother Bord , i want to change boot sequence, can u pls tell me how to do it. thanks


BIOS is a software program that controls basic functions in your computer, such as boot order, keyboard control and how your processor interacts with memory cards. If you get an "NTLDR Is Missing" error, inspect your BIOS utility to make sure your computer is booting up from the right place.
During the boot process you will see on the screen to press a certain key to enter setup
Press and hold that key during the boot up process to enter BIOS
after you make any changes in BIOS press Esc then press the F10 button save to cmos to restart
cmos is located in BIOS
hope this helps

May 21, 2011 | MSI PM8PM-V (7222080PM8PMV) Motherboard

1 Answer

Self having the following configuration on Home desktop PC. INTEL 1.7GHz, P4, D845GBV motheboard with AGP ATI Radeon 9000 graphics card, RAM is 2 x DIMM DDR2 266 Hz, 1 x 1GB + 1 x 512MB total 1.5GB RAM....


Power down and disconnect AC power from your PC. Remove the AGP card and DIMM again and use some "canned air" or dusting spray to get any dust off the contacts on your motherboard and your memory and AGP card. Wiping the AGP card contacts with some isopropyl alcohol (also known as IPA or "rubbing alcohol") and a clean, lint-free cloth can also help. When everything is dry, put your card and memory back in and try powering up again.

Mar 21, 2011 | Intel D845GBV (BOXD845GBVL) Motherboard

1 Answer

Cmos battery replaced already but still system


Hi
You can disable the halt errors
In the bios

Jul 13, 2010 | Intel Motherboard

2 Answers

When i start windows computer sounds a beep and a information screen opens with system specifications and shows "A: Drive error Press F-4 to rsume" whats the problem with my board please?


Hello,
This error comes due to the Floppy Drive error..pls check the floppy drive cable connector prperly connected or not ...If there is no floppy drive ..Go into BIOS setup and disable the floppy drive..Then this error wont come again ..
Thank You for using FIXYA!!!!!!!!

Dec 04, 2009 | Intel D865GSA (BOXD865GSAL) Motherboard

1 Answer

Clarification about my foxconn bios checksum error


try to change cmos battery...
or
flash BIOS
download bios from bellow link
and pls refer the manual.
http://www.foxconnchannel.com/support/downloads.aspx?ProductModel=661FX4MR-ES&TypeID=en-us0000004
thnaks
if ur problem solve so pls rate me..
bye

Mar 05, 2009 | Foxconn 661FX4MR-ES Motherboard

1 Answer

Bootblock


Hi,

This messages indicates that the BIOS could not be located and loaded up. Normally this happens when the BIOS is corrupted. The corrective action required is to re-flash the BIOS using a DOS bootable diskette in the 1.44 FDD. Aside from the BIOS file, a flashing software is also needed. Pls start here.

Hope that this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Oct 22, 2008 | MSI K9VGM-V Motherboard

1 Answer

Cannot view windows setup screen


first you must configure your bios..set the first boot with cd rom and disable the HDD.

then exit. and insert your installer for windows. and setup will follow.. hope this would help.

Oct 02, 2008 | Motherboards

1 Answer

Help me pls


Hi,

First you need to have a Floppy Drive installed on you computer, then Second you need a stat-up disk.

You also need to download the BIOS File Update on this link

http://www.ecsusa.com/ECSWebSite/Downloads/ProductsDetail_Download.aspx?
CategoryID=1&Typeid=2&detailid=59&DetailName=BIOS&DetailDesc=P4VXASD(V1.3)
&MenuID=39&LanID=9

Then you also need to download an AMI FLASH Utility Software to upload the BIOS FILE Update on your motherboard, you can use the link stated on that link above.

If this procedure solves your problem, please spare a little time to rate my solution.

-mrsolution

Jun 12, 2008 | Intel Motherboard

1 Answer

Problem on o/s installation


Look in your bios & see if you can disable the ACPI, (which you should be able too do. Finish installing your OS. Than update the OS. After completing all updates re-enter your bios & enable the ACPI. You should not get that error message after re-start.
Boards that support ACPI will get this error during a fresh install untill they get windows updated. All OS's
Post back if this did not help! It worked for me.
Please vote..

Jan 28, 2008 | Intel D945GNT Motherboard

Not finding what you are looking for?
Intel D845GVSR Motherboard Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2598 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Are you an Intel Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...