Question about Washing Machines

3 Answers

Wont start has error DE

We had a power cut yesterday and now the washer won't start - keeps showing error of DE - have turned it off for 20 mins then on again but still the error DE we moved recently & I have lost the user guide with the trouble shooting section in it - can you please tell me how to 'reset' the panel thanks - Wendy

Posted by on

  • 1 more comment 
  • WENDY FONTANA Dec 07, 2008

    the make is a Samsung Triflow top load washer model SW65ASP2

  • WENDY FONTANA Dec 07, 2008

    THANK YOU FOR THE REPLY BUT I MANAGED TO SOLVE THE PROBLEM - IN SOME OF THE RESULTS ON THE 'DE' ERROR I FOUND IT MENTIONED THE LID - I CHECKED THE LID AND SAW THE MAGNET ON THE LID HAD BEEN DISLODGED AND WAS NOT SITTING WERE IT SHOULD - I REPLACED THE LID MAGNET AND THE ERROR 'DE' WENT AWAY AND MY MACHINE STARTED TO WORK OK!!
    THANKS A LOT ANYWAY

  • Neil Golan
    Neil Golan May 11, 2010

    Send the complete model number and I will help you!
    Huum


×

3 Answers

Your door interlock has failed
and needs replaced

DE is door not locked in a think 5 makers machines error codes

DOOR ERROR is what it stands for

so its a simple repair

you take the top off the machine with power water etc off
and open the door
take the two screws out its lock or unclip it plastic locking clamp
being careful not too damage it
then reach down to the door lock
and unclip the bad interlock mecha
having ordered one from ebay etc
then plug the usually 3 pin to the new interlock and reach down
and relocate it
and screw in the two screws or replace the clip plastics

then
put the machine back water and drain
and then mains

but when you turn the mains on
press and hold either power on or start stop
for 10 seconds then let it go

prob the machine will beep
then do a no washing test
place it on drain spin and see what happens

if you have a DE then the controller board prob has an issue

and thats my spiel

Posted on Apr 28, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have samsung waching machine -gives out DE error -door is perfect- the water is perfect what could be other causes how to fix it please advice

Posted on May 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Error displayed Wont start has error DE - table_1.gif Solution
n_de.gif table_2.gif Close the door. Wont start has error DE - n_4e.gif n_4e.gif table_2.gif i_1.gif Make sure the source water faucet is turned on.
Check the water pressure. Wont start has error DE - table_2.gif
Wont start has error DE - i_1.gifc="http://i.fixya.net/uploads/images/n_5e.gif" alt="n_5e.gif" class="h_mi" /> table_2.gif i_1.gif Clean the debris fiWont start has error DE - n_ue.gif /> Make sure the drainage hoseWont start has error DE - i_1.giftalled correctly.
n_ue.gif table_2.gif i_1.gif Laundry load is unbalanced; loosen any tangled laundry. If only one iteWont start has error DE - n_ce.gifthing needs
washing, such as a baWont start has error DE - n_3e.gifr jeans, the final spin result might be unsatisfactory and an "UWont start has error DE - table_2.gif error message will be shown in the display windoWont start has error DE - i_1.gif/>
n_ce.gif
n_3e.gif table_2.gif i_1.gif Call after-sa

Posted on Dec 07, 2008

  • Neil Golan
    Neil Golan Dec 07, 2008

    Can you please leave a rating before you leave. this is important

  • Neil Golan
    Neil Golan Dec 08, 2008

    Can you please leave a rating before you leave. This is important



×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed door switch on my kenmore h2 plus cause of error code and it still wont work


Whirlpool & Kenmore Dryer Repair #01 - Won't Start or Run ...

? 8:50
https://www.youtube.com/watch?v=2WF71WdGn_g
Oct 19, 2011 - Uploaded by canyonman1963
This one deals with testing and replacing the door switch. ...sears wont work wont spin wont wash wont heat wont start fix repair bad noise noisy ... how to change a 4 to a 3 prong cord, to figuring out my door switch problem.

Dryer Door Switch - How To Replace - YouTube

What to do when your washer won't fill, start or run - YouTube

? 2:00
https://www.youtube.com/watch?v=Atd5YHbRh7M
Jun 20, 2012 - Uploaded by searspartsdirect
So if my washer wont start just call Sears. .... Bad sears mykenmore is only 2 years old, fill take 30 mins,,,wash 50 mins rinse never spin never,, ...


Nov 28, 2015 | Kenmore Washing Machines

1 Answer

Harmony washer power touch screen not work


Make sure all connections are secure. Make sure you have power to the screen and all.

Feb 06, 2014 | Washing Machines

2 Answers

My washer is showing dE message what is this mean?


The machine identifies and indicates some operational errors through a series of beeps.As you are using LG WM2455 Front load Washer it is showing error message The error message "DE" This error signal beep during drain.Unhook/clean drain pipe and press the 'Start/Pause' button to continue cycle.Thanks for your question.

Jun 17, 2011 | LG WM2455 Front Load Washer

1 Answer

Hello. I have samsung wf8604nwg washingmachin.and now theres a message that says HEI at the screen. what can i do to fix this?


WATER HEATER ERROR - Display shows HE, HE1.

HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. The error can be cleared by turning POWER switch OFF.

Jan 01, 2011 | Washing Machines

1 Answer

Problem with the Samsung Washing Machines The machine keeps coming up with the message HEI 10x


Here is a list of errors for your machine.

I hope they help you.


SAMSUNG WASHING MACHINES, ERROR FUNCTIONS

When an error occurs, the alarm noise will sound and the error code displayed in the program window. Listed below is a series of error codes you may or may not see for your model of Samsng Washing Machine. The errors are shown as blinking in O.5 second intervals until the error status has cleared. In this case, all the driving devices are turned off until the error is cleared.

1. WATER SUPPLY ERROR - Display shows 4E.

Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply. The error status can be cleared by turning the POWER switch OFF and back ON.

2. WATER DRAIN ERROR - Display shows 5E.

5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.

3. OVER-FLOW ERROR - Display shows oE.

Over-Flow error occurs when the water level is too high. It can be cleared by turning POWER switch OFF. Water is drained prior to POWER switch OFF. The tub is drained for 2 minutes if a frequency of more than 25 KHz is detected.

4. UNBALANCE ERROR - Display shows UE.

Laundry load is unbalanced, manually loosen any tangled laundry.

If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.

5. WATER HEATER ERROR - Display shows HE, HE1.

HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. The error can be cleared by turning POWER switch OFF.

6. WATER PRESSURE SWITCH ERROR - Display shows 1 E.

* Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz)

Normal Level = Abnormal W/L Frequency
Low Level = 30.00 Khz
High Level = 15.00 Khz

If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error. When this error occurs the drain pump will operate for 3 min. and the display will show 1 E indicating a pressure switch error.

7. ABNORMAL WATER TEMPERATURE ERROR- Display shows cE.

e.g. If the water temperature is 50 C or more, during a Delicate or Wool cycle.

At the time of initial water supply, if the water temperature is not appropriate, the display will show cE. This error can be cleared by POWER SWITCH OFF.

8. WATER LEAKAGE ERROR - Display shows 11 E.

Water Leakage error occurs when the water drains naturally, (by leakage) after the washing program starts.

9. THERMISTOR ERROR - Display shows tE

Nov 21, 2010 | Washing Machines

1 Answer

THE DE ERROR CAME ON MY WASHER WHAT DO I DO/


Hi,
A DE Error Code is indicative of a “Door Error”. This indicates that the washing machine door is not shutting, locking or opening

If happening in mid cycle power of the unit and remove the power cord and wait for 5 mins.Then plug it. Check whether the door opens if not you require the service people


Check anything is caught on the washer door.


If you passed it they door may not open if the inside water is warm.It is a safety feature.It unlock after sometime


Thank You

Sep 09, 2010 | LG WM-2077C Front Load Washer

1 Answer

LG- WM2355C Wont lock and start spinning. Shows


Unplug the washer for fifteen minutes and if that doesn't it is your lock mechanism. You will need a repair man or if you are handy you can do it.

Dec 07, 2009 | LG WM-2277HW Front Load Washer

1 Answer

I have a l.g. steam washer screen says error


Unplug it for 10 minutes.  Press and hold SPIN SPEED and SOIL LEVEL buttons WITH POWER OFF.  With both buttons held turn the power on and press START/PAUSE till you hear the drain pump operating.  If it is the brand new one it will be 12 times.  Once all of the water is drained out turn the machine off, then back on and the door should unlock.  If you keep getting an error, you should call for service.  All new machines come with a 1 year parts and labor warranty

Oct 24, 2009 | LG WM2688HWM TROMM SteamWasher

1 Answer

Error Code F-20


I have same machine and manual says, "F20" on display (water inlet problem - no water or insufficient water supply). Select STOP twice to cancel the cycle. Unplug washer or disconnect power. Check the following. Are water faucets completely turned on? Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked? Are water inlet hoses frozen? Plug in washer or reconnect power. Re select cycle and press START. if the problem remains, call for service.

May 13, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Random electrical problems, sometimes it works beautifully, sometimes not!


F11 = Communication between the Central Control Unit (CCU) and the
Motor Control Unit (MCU) cannot be sent correctly.
.
1. Unplug washer or disconnect power.
2. Check wire harness connections to the MCU, the motor, and
Central Control Unit (CCU).
3. Check the drive system for any worn or failed components.
4. Plug in washer or reconnect power.
5. Verify CCU operation by running a Diagnostic test or any
cycle.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.
8. Check that the serial harness at the MCU is not mounted
upside down. The wires should be to the left when facing the
MCU connectors.

FDL=
A Door Lock Error occurs if the door cannot be locked. It will try to lock
it six times before displaying the error code.
Le code d’erreur “Verrouillage porte” apparaît s’il n’est pas possible de verrouiller la
porte. Le système effectue six tentatives de verrouillage avant d’afficher le code d’erreur.
■ Door lock mechanism is broken or removed from door.
■ Door switch/lock unit failure.
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door
switch/lock unit and Central Control Unit (CCU).

Feb 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

707 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...