Question about Kenwood DV-605 Multi-disc DVD Player

1 Answer

Re: Kenwood DV 605 CD Player... Power On: Reads "Loading." All 5 CD lights are lit up but the CD changer does not turn. CD #1 appears on screen with two green lights appearing.

Posted by on

  • Anonymous Jan 05, 2009

    Yay!  This fixed mine, too!  You ROCK!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Re: Kenwood DV 605 CD - ace71cf.jpg We repaired this problem by taking the advice of another member of FixYa! The component had recently been packed to be shipped. After unpacking the unit when we powered up the read out only displayed "LOADING" and the CD changer door would not open. We removed the exterior cover and gently moved the CD changer one position. When it locked back into position we powered up and the unit works fine now. FixYa sure help me save perhaps a $100. or more by not sending it to the manufacturer or another shop. And it was working within minutes so we could enjoy using it right away. Thanks guys I very much will recommend this sevice to others... this was the 2nd problem we fixed that day by logging onto FixYa!!!

Z-Dawg

Posted on Dec 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic BTT268 tray wont open


Dear Scott,

If there is a CD stuck inside a CD/DVD reader, you could try using a medium sized paper clip straightened up. Insert it in the small hole in the front of the DVD player bezel and push it till it opens the mechanism. Please, have a look at: http://www.youtube.com/watch?v=fa_4CsS7MKw

The problem can also be caused if one of the rubber band that moves the DVD drive "door" has dried out, or even if the power supply in not properly connected to the drive.

Hope you may find this info hopeful!

Best regards,

Miguel Luiz Martins

Nov 19, 2013 | Kenwood DV-605 Multi-disc DVD Player

3 Answers

Stopped playing after I inserted damp CD in 200 disc loading mechanism


this can be due to some moisture in lens.

leave the unit to get dry for 2 days.

Jul 04, 2008 | Kenwood DV-5700 Multi-disc DVD Player

1 Answer

Only shows loading on face of player


either some how the remote has become unsinked or the reciever is bad in it

May 22, 2012 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

It is displaying a loading but there is no disc and it will not move. I have reset it like it says in the manual but no luck.


yes bad electronics took mine apart put it back together it worked fine till i turned it off . you have to tap or hit the front above the buttons and sometimes move stuff around then it will work wires boards but be sure its not plugged in

Sep 07, 2009 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

DVD tray makes noise when it rotates


This noise can be casued by two things:

1) The tray is not completely in the loaded position and the "clamper" is rubbing. Replace the loading belt and the loading sequence will complete and the noise should stop.

2) The "CD table" that is part of the spindle motor assembly has slipped a bit. This will make the CD/DVD ride too low and strike the lower tray support. This will require that the table be "re-aligned" to the proper height which may not be possible on your model without special measurement equipment. The height is critical to proper operation of the unit.


Try replacing the load belt first and report your results.

Thanks,
Dan

May 30, 2009 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

Tray will not open on my dv-605


Solution: Unplug power from wall. (Don't just turn off!) Next: Remove exterior case. Now gently turn the CD changer clockwise one position. Power up and try again.

I had this same problem after unit appeared to have froze up when unpacked from a shipping box. The CD changer had got off track and by gently moving the CD changer 1 position it fixed the problem. Works fine now.

Best of luck,
Z-Dawg

Apr 30, 2008 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

Disk error with Kenwood DV-605 multi-disc DVD player


Try the following
when the error is on the screen, press the number 1 key on the remote, this should take you to the fist chapter of your DVD no matter which region it is

Miguel

Jan 03, 2008 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

Dv-605 kenwood


I have a similar issue with my DV-605 as well. When the unit power on, I can hear the motor trying to start, but the DVD does not spin. Being the adventurous type, I opened the case and turned the DVD drive motor a few revolutions by hand and then the dvd played. I think I need a new DVD drive motor. You may as well....

Dec 09, 2007 | Kenwood DV-605 Multi-disc DVD Player

1 Answer

DVD


I just fixed mine. Same scenario, with the loading and #1 displayed. The tray changer was jammed.

Take the cover off the unit and gently convince the changer to spin. It will go *crack* and then exhibit free-play. Turn the machine back on and voila it works.

I'm now watching Braveheart on 480p on 55"widescreen!!!!!

Wally

Oct 27, 2007 | Kenwood DV-605 Multi-disc DVD Player

Not finding what you are looking for?
Kenwood DV-605 Multi-disc DVD Player Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood DVD & Blu-Ray Players Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

378 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you a Kenwood DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...