Question about LG 4.0 Cu. Ft. 7-Cycle Front-Load Washer - White

1 Answer

Receiving an le display.

Can we do anything besides call for a repair man? It was working fine and then all of the sudden le.

Posted by on

  • Christophe Thompson
    Christophe Thompson May 11, 2010

    do you have little critters running round i found this recently that little critters get into the board and then die creating an arch aross points and it can be quick last night i witnessed it happening to my sterio as they tried changen the volume on me open up back carfully pull out circuit board carefully see if the little critters moved in

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • LG Master
  • 2,651 Answers

You more than likely have a bad RPS sensor, dont know if i would want to mess with that, you could wind up damaging the motor/rotor in process of getting to

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We are at our wits end. See details. What else can we do? LG Tromm 2277 Washer no power.


either of 2 things I can suggest . 1 would be call the repair man or 2 buy a new one .

Oct 05, 2014 | Washing Machines

1 Answer

My LG WM2301HR front load washer fills fine and rotates In both directions as it fills but will not rotate during the wash cycle. It vibrates a little like it wants to but then stops all together and...


LE = Locked motor Error

• The connector in the LEAD WIRE ASSEMBLY is not connected to
the connnector of STATOR ASSEMBLY
Reconnect or repair the connector
• The hall sensor is out of order/defective.
Replace the STATOR ASSEMBLY

Sep 18, 2014 | Washing Machines

1 Answer

LE error on washer. What can I do without a tech?


The *dreaded* "LE" error is overwhelmingly caused or triggered by incorrect type detergent **OR** too much *HE* detergent (a special low sudsing detergent).
In all LG washers-when too much detergent has been used-this will cause the "LE" error to be displayed & the wash cycle will be interrupted. Unplugging the washer for more than one minute will cause the MAIN BOARD (computer) to power down and re-boot when the washer has been plugged back in.
On LG washers built *before* 2008-after several "LE" error events-the error *cannot* be reset by unplugging the washer. This indicates that the HALL EFFECT SENSOR has failed and will need to be replaced.
On all LG washers built during and after 2008-a more robust resistor was used in the HALL EFFECT SENSORS-which eliminated damage caused by higher electrical loads placed upon the sensors due to oversudsing. HALL EFFECT SENSORS virtually never fail in 2008 and newer LG washers but the "LE" error will still occur if too much or the wrong type of detergent is used. This will be "resettable" by unplugging/replugging the washer.
The CORRECT amount of HE (High Efficiency) detergent to be used is as follows:
HE : (2) Tablespoons Per Wash Load
HE 2X : (1) Tablespoon
HE 3X : (1) Teaspoon
USE THESE AMOUNTS RELIGIOUSLY-NO EXCEPTIONS-IN ALL FRONT LOAD WASHERS WITH 3.0 cu ft DRUMS AND LARGER

Read more: The Dreaded LE Error Code in LG Washing Machines: Diagnosis / Troubleshooting, Root Causes, and Repair ' Washer Repair ' Fixitnow.com Samurai Appliance Repair Man http://fixitnow.com/wp/2010/08/03/the-dreaded-le-error-code-in-lg-washing-machines-diagnosis-troubleshooting-root-causes-and-repair/#ixzz2nlabX1Gv
Follow us: fixitnowsamurai on Facebook

Dec 17, 2013 | LG WM2233H Front Load Stacked Washer /...

2 Answers

Le Error on front load machine


Hello,This a common problem for all front loaders. Your washer will not drain or work 'cause your outlet filter is clogged. Usually this small door is on the left side front below of your washer. Expect some water to come out when you open the door, etc. Clean out your filter and refit.....things should be fine.

Thanks

May 22, 2010 | LG WM-2277HW Front Load Washer

1 Answer

LG Tromm WM2077CW error code LE


Hi,
No all you have to do is watch how much and what kind of soap you put in that washer...

http://www.fixya.com/support/r4348161-lg_washing_machine_le_error_code_or

heatman101

Apr 15, 2010 | LG WM-2277HW Front Load Washer

1 Answer

LE Error code


Hello,

SOUNDS LIKE LOCKED ENGINE. SEVERAL DIFFERENT THINGS CAN CAUSE THIS ERROR CODE TO BE DISPLAYED.

1ST, USING THE WRONG SOAP WILL CAUSE THIS PROBLEM - USE HE SOAP ONLY!!! - IF YOU HAVE BEEN USING THE WRONG SOAP, BEFORE CALLING FOR SERVICE I WOULD ADVISE YOU TO RUN A FEW SHORT CYCLES WITH HOT WATER ONLY - THIS SHOULD HELP IN REMOVING ANY SOAP RESIDUE FROM THE SOAP SENSOR AND BOOT AREA.

2ND, THE CONTROL BOARD MAY BE DEFECTIVE - YOU NEED TO CHECK VOLTAGE OUTPUTS TO VERIFY.

3RD, BE SURE TO CHECK THE WIRING HARNESS - IT HAS BEEN KNOWN THAT WIRES SOMETIMES BECOME FRAYED AND LOOSE RESISTANCE.

4TH, THE SOAP SUDS SENSOR MAY BE FAULTY AND NEEDS TO BE REPLACED.

Regards
ami-man

Dec 04, 2009 | LG WM1812C Front Load Washer

1 Answer

Display says LE


I am not a repair professional. I am just a 78 year old man who has been making his own repairs for about 50 years. Therefore the washer ID doesn't mean
anything to me. It's been about 55 years since I had experience with front load washers. However I can refer you to www.applianceaid.com where they have very good and complete trouble shooting and repair information on front loaders. I think you'll find what you need there. Don't worry about the timer, they hardly ever go bad. Good luck with it. If I have helped you, please rate my advice on fixya.

Nov 25, 2009 | LG WM-2277HW Front Load Washer

3 Answers

I have an LG WD 3243RHD washing machine/dryer combo and it is displaying LE. Is there anything I can do without calling a repairman?


LE on this machine indicates a motor error. The connector in the lead wire assembly is not connected to the connector of the stator assembly. You need to reconnect or repair the connector. Also, it could mean that the Hall Sensor is defective and you may need to replace the Stator Assembly.

Nov 09, 2009 | LG WD-3243RHD Front Load Washer / Dryer

1 Answer

WASHER FILLED WITH WATER AND STOPPED WORKING COMPLETELY


if you hear a motot running the coupling between the motor and transmission has disinagrated.

Dec 26, 2008 | Maytag MAT12CS Top Load Washer

1 Answer

LE fault code for LG WD-1019bd washer


Usually it is the stator at fault with an LE error. I would make sure the cable between the stators windings and hall sensor are ok back to the main control board also give the wires a good tug sometimes the copper breaks inside the wiring insulation at the white connection blocks. Check to make sure theres nothing got trapped inbetween the drum and tub this can lock the drum up and give the fault. After checking all the above i would think it would either be a faulty stator or the main control board has failed. Hope this helps.

Dec 21, 2008 | Washing Machines

Not finding what you are looking for?
LG 4.0 Cu. Ft. 7-Cycle Front-Load Washer - White Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...