Question about GE Cooktops

2 Answers

GE Profile Cooktop was just cleaned and the burners cont. to clic

When we unplug the cooktop, the clicking stops. As soon as we
plug it in it starts to click again. Is there some other way we
can get our cooktop to the way it was before we cleaned the
burners. We just used soap and wataer.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This always works for me but it so sensitive to any moisture that I no longer take off the knobs to clean; I hate it. After the house cleaners came 5 days ago one knob is still active and clicks.

Posted on Feb 28, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 324 Answers

You must have gotten water down the igniter switches.try drying out underneath the knobs. or leave unplugged till they dry.

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Piezo igniter won't quit


Possible stuck burner switch or failed spark module. Unplug unit. Remove wires from burner switches at module and plug back in. If it starts sparking, replace module. If it stops, then replace switch harness.

Jan 18, 2011 | GE 30 in. Profile JGP932 Gas Cooktop

1 Answer

Striker on gas profile cooktop will not stop striking. will only stop if electic is turned off.


Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking

heatman101

Aug 29, 2010 | GE 30 in. Profile JGP933 Gas Cooktop

1 Answer

My ignition for the gas cooktop is clicking without being in the on positoin. will this be caused by cleaning with water? is it going to cause problems?


One of your burner ignition switches is fried. To see which one it is you remove a wire from each one till the ticking stops. Or plan be just unplug the stove and light it with a match.
23498b2.png34c6129.jpg

Mar 12, 2010 | GE Profile JGP636 Gas Cooktop

1 Answer

Have a four burner gas GE Profile cooktop. How do


The igniter module is working fine. One of the switches (which are on each valve shaft) is stuck or shorted out. Pull a wire off each one at a time to determine which one is bad. Careful! 120 volts to each wire. Also, this can happen after you spill water into the valve area, if that sounds right, let it dry out.

Jan 29, 2010 | GE 30 in. JGP328 Gas Cooktop

1 Answer

Dcs igniters


clean the knob control by using vaccium,pull the knobs then clean it.make sure how to remove the knob,same position to returrn the knob

Jun 30, 2009 | GE Profile JGP636 Gas Cooktop

1 Answer

Ignition will not stop clicking...


Did you clean your stove recently? If the switches under the burner knobs get wet they will cause the burners to click. Unplug the unit or shut off the power for a day. Once the swithes dry, it should work normal.

May 05, 2009 | GE 30 in. Profile JGP932 Gas Cooktop

1 Answer

We have a 5-burner GE cook top/ The igition for the center burner continually fires.


the spark modual is bad in the cooktop. you can just leve it unpluged and light with a match until you can get it replaced

Nov 22, 2007 | GE 36 in. Profile JGP962 Gas Cooktop

Not finding what you are looking for?
Cooktops Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Cooktops Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

meztang
meztang

Level 2 Expert

112 Answers

Are you a GE Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...