Question about Extended Systems PocketPro Print Server

1 Answer

How to reset Pocket Print server Extended Sys ESI 2833?

How can I reset it so it can accept a DHCP server IP address?

Posted by on

  • tndf Apr 08, 2009

    i ve got the same problem. My pocketPro is already configure with an IP and i want to reset it.

  • Anonymous Mar 26, 2014

    SOFTWARE TO RESET IP ADDRESS

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Disconnect the power. Press the small test button and keep it pressed, while you reconnect the power AND wait until the green LED is on again.

Posted on May 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jetdirect ex default ip


Usually it it set to pick up IP from DHCP/BootP.
If someone had assigned a fixed IP and it is now unknown. It is better to reset the print server to factory default by pushing the little reset button,
Then check you DHCP server for the newly assigned IP address.

You will need a version of HP Jetadmin or HP webjetadmin to configure this print server

May 13, 2014 | HP JetDirect EX Plus Print Server

1 Answer

Reset ESI 2833 until red light turned green. Network Printer still not responding


Check the IP Address of the 2833. I believe there is a gray button you can depress to print out a configuration sheet. If the wireless modem was also your router, you may have a different IP address range and will need to set the 2833 accordingly.

Sep 03, 2013 | Extended Systems Pocket Print Server

1 Answer

Change ip address on extendnet mpx


There should be a software program that allows you to change the IP Address that came with the unit. If you don't have that, you would need to reset the unit to factory defaults (which may not be possible without the software) set the device in the same subnet as your DNS router, change the BOOTP/DHCP table with the MAC Address and new IP Address.

Feb 20, 2013 | Extended Systems ExtendNet MPX Print...

1 Answer

I have an extendnet sx ESI-2811 Print Server. It doesn't work and I can't ping it when directly connected to my laptop via ethernet cable. It must be broken. Any ideas?


Use a crossover cable to connect laptop directly. Does your print server have a static IP address and do you know what it is? If yes, set a static IP on your laptop that is in the same subnet and with the same mask, then you should be able to ping it. If the print server is obtaining an IP by DHCP, you will have to set up and run a DHCP server on the laptop (or connect it with a straight-thru cable to an existing router that offers this service).

Jun 21, 2010 | Print Servers

2 Answers

My network HP laserjet 4Vprinter and ESI 2830 pocket print server suddenly gives an error message "No RARP/BootP Server". How can I fix this?


the information in the link is too long to paste but you may want to look at it.

HP Jetdirect and Embedded Jetdirect Inside Print Servers - TCP/IP, Messages on Configuration Page or Self-Test Page

Get the IP address subnet and gateway address of a computer in the same network.

Usingthe LJ5's control panel, setup a static IP for the Jet Direct using thenumbers you got from the Laptop, except change the last number of theIP to one that is not being currently being used. Perhaps adding 5 or10 to the highest number in use.
Here are the steps to configure the LJ5.

1.Press MENU, repeatedly, until the following message appears on thecontrol panel: HP LaserJet 5/5n/5m and the original Color LaserJet: HPMIO MENU
2. Press ITEM. CFG NETWORK=NO* will appear.
3. Press the PLUS button once. CFG NETWORK=YES* will appear.
4. Press ENTER or SELECT.
5. Press ITEM repeatedly until CFG TCP/IP=NO* appears.
6. Press the PLUS button. CFG TCP/IP=YES* will appear.
7. Press ENTER or SELECT.
8. Press ITEM until BOOTP=YES* appears.
9. Press the PLUS button. BOOTP=NO will appear.
o When using BootP or DHCP, keep the setting BOOTP=YES*.
o The BootP or DHCP server will configure the TCP/IP parameters on the HP Jetdirect.
o No other TCP/IP configuring is necessary.
10. Press ENTER or SELECT.
11. Press ITEM. IP BYTE 1 = (value) will appear.
12.Press the PLUS button until the value of the first byte of the IPaddress appears on the control-panel display. By pressing SHIFT and thePLUS button, the value will decrease.
13. Press ENTER or SELECT.
14. Press ITEM to continue. Repeat Steps 11-13 to configure the remaining bytes of the IP address.
15.Repeat Steps 11-13 to configure the subnet mask bytes (SM BYTE 1=),syslog server IP address (LG BYTE 1=), default gateway (GW BYTE 1=),and timeout (TIMEOUT=).
16. Press ONLINE. Print a self-test page to verify the IP settings.
17. If the test page does not show the correct settings, power cycle the printer and reprint the test page.


else: have the printserver reinstalled
www.nls.com/common/pdfs/v307n10.pdf

Nov 24, 2009 | Extended Systems Pocket Print Server

1 Answer

How to install pocket printer server


Your DHCP server will keep track of which MAC Addresses have been given what IP addresses. From there, find the IP address of your Print Server. Ping the IP address to confirm IP connectivity between your computer and the print server. You should then be able to upgrade the firmware.

Aug 07, 2007 | Emulex NetQue Pro2 (NP02) Print Server

3 Answers

ESI-2831 Drivers missing


Here is a Manual. As for the drivers came up short on them sry. www.nls.com/common/pdfs/v307n10.pdf

Apr 19, 2007 | Extended Systems Pocket Print Server

1 Answer

Can't find printserver on the network


Most Print Servers are by default on DHCP and if the PS is still on its factory defaults, it won't get an IP address because your computer won't have a DHCP server (unless u have set up one). Now, you can ask the person you got it from if he had ever assigned a static IP Address to the PS. Also, one of the reasons why your laptop won't detect the PS might be a software firewall installed. Please revert back with any other questions or observations. good luck

Mar 23, 2007 | Extended Systems Pocket Print Server

1 Answer

ESI-2833


User: admin Password: extendnet

Feb 21, 2007 | Extended Systems PocketPro Print Server

2 Answers

Cannot find print server at all


How this works: Restoring the PocketPrintServer to Factory Defaults In most cases, the best way to restore the PocketPrintServer to factory defaults is through "telnet". However, if you are unable to connect to the device because of a configuration error, use the following method which does not require a network connection. To restore the PocketPrintServer to factory defaults, complete the following steps: 1. Disconnect the PocketPrintServer from the network and power cycle it. When it powers up, the LED will rapidly blink orange for five seconds. 2. Power down the device during the rapid orange blink period. Power up the device and power it down during that orange blink period two more times. 3. Reconnect the network cable and power up the PocketPrintServer. It will have restored itself to factory defaults and will rapidly blink green as it searches for a RARP or BOOTP server to find an IP address. Gleaning If an IP address has not been permanently assigned when the PocketPrintServer is powered on or reset, it will look for a "ping" packet on the network. If the PocketPrintServer receives a "ping" packet within two minutes, it will accept the IP address in the "ping" packet as its own address. To use Gleaning, you must have super-user privileges on a UNIX system. Gleaning also works under Windows 95 and Windows NT. 1. Add an entry in the ARP table that assigns an IP address to the Ethernet address of the PocketPrintServer. To do this, use the "arp" command. arp -s temp Example: arp -s 192.168.42.24 00:02:16:00:00:01 temp 2. Start a continuous "ping" to the PocketPrintServer. ping Example: ping 192.168.42.24 On some systems, this may require an additional parameter. Some implementations of "ping" only send out one "ping" packet which could get lost in transit. Check your system documentation for more information. 3. Connect power to the PocketPrintServer. The PocketPrintServer will "glean" its IP address from the "ping" packet. This IP address will remain in effect until the PocketPrintServer is power cycled or reset. Therefore, a permanent IP address should be assigned by running the ExtendView TCP/IP utility or via "telnet".

Jan 30, 2007 | Extended Systems Pocket Print Server

Not finding what you are looking for?
Extended Systems PocketPro Print Server Logo

Related Topics:

2,142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Extended Systems Print Servers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

old marine
old marine

Level 3 Expert

1479 Answers

Cindy Wells

Level 3 Expert

4762 Answers

Are you an Extended Systems Print Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...