Question about Tektronix Phaser 740P Laser Printer

1 Answer

ERROR 22 My printer shows error 22 after initialization.

Posted by on

  • tariqjaved50 Dec 07, 2008

    Open the imaging unit. Clean the rubber coated rollers with petrol. Grease the ball bearings, clean the waist toner and the re-assemble it.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 162 Answers

You Need to Try One Of The Following :

Remove and re-install Imaging Unit (make sure that Imaging Unit
is locked in place). Turn the printer off, then on.

Replace Imaging Unit (make sure that Imaging Unit is locked in
place). Turn the printer off, then on.

If problem persists for Error 30, clean the sensor.

If problem persists, check www2.tek.com/merlin/tko and/or
contact Service.

Posted on Dec 05, 2008

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to solve scanner error 22 in HP laser jet 1213mfp


Perform a power reset.
Press the Power button to turn on the printer.
With the printer turned on , disconnect the power cord from the rear of the printer.
Wait at least 30 seconds. Reconnect the power cord to the rear of the printer.
Press the Power button to turn on the printer.

update the firmware by download from this link: HP LaserJet Pro M1213nf Multifunction Printer Drivers

Jan 20, 2015 | HP Office Equipment & Supplies

1 Answer

Error no 22:10 how to solve for hp 500 Plus


Back up EEPROM failed which was located in ISS( Ink supply station) & need to replace.. But this is major issue, only professionals can do this activity, other wise both ISS & Electronic module's will effect.
This is only one major activity in 500 & 800 series.
Pl consult HP trained professionals..

Nov 03, 2012 | HP DesignJet 500 InkJet Printer

1 Answer

Scanner error 22 M1213nf mfp


why it is showing scanner error 22 message

Feb 23, 2012 | HP LaserJet M1120 MFP All-In-One Printer

1 Answer

Panasonic dp-cl22 error 66


Try uninstalling the printer.

Go to Panasonic Website, download & install drivers.

http://www.panasonic.net/pcc/products/printer/download/dp-cl22download.html

Let me know if you need more help.

Jul 24, 2009 | Panasonic WORKiO DP-CL22 Network Color...

1 Answer

ERROR E1-22


uve a problem with ur laser unit im affraid needs to be replaced

Jan 16, 2009 | Panasonic Workio DP-3530 Copier

1 Answer

Error 2210


Ink Supply Station failure
The possible cause could be:
1. Reading, writing or initializing the backup EEROM failed.
2. One of the out-of-ink sensors (located in the Ink Supply Station)
is not reporting what it should during the initializing process
while depressurizing.
Corrective Action: Replace the Ink Supply Station

Aug 29, 2008 | HP DesignJet 500ps InkJet Printer

2 Answers

Printer takes ages to process


NV RAM and HD
To initialize NVRAM
1. Remove any installed accessories (for example, a stapler/stacker).
2. Turn the printer off.
3. Hold down the DOWN ARROW ( ) button, and then turn the printer on. Continue holding
down the DOWN ARROW ( ) button until all three printer control-panel lights flash once and
then remain on. This might take up to 10 seconds.
4. Press the UP ARROW ( ) button.
5. Press the PAUSE/RESUME button. The display should show SKIP DISK LOAD.
6. Press the UP ARROW ( ) button until NVRAM INIT is highlighted.
7. Press the SELECT ( ) button. The printer initializes NVRAM and then continues its poweron
sequence.
Hard-disk initialization
CAUTION A hard-disk initialization erases and reformats the printer hard disk. Perform a hard-disk
initialization only if an error code on the control panel indicates an EIO disk error. Always try
initializing the hard disk before replacing it.
NOTE Before performing a hard-disk initialization, print a menu map and a configuration page (see
Menu map and Configuration page). Use the information on the configuration page to reset
any customer-set printer configuration values that the hard-disk initialization procedure
changes.
To initialize the hard disk
1. Turn the printer off.
2. Hold down the PAUSE/RESUME button, and then turn the printer on. Continue holding down
the PAUSE/RESUME button until all three printer control-panel lights flash once and then
remain on. This might take up to 10 seconds.
3. Press the BACK ARROW ( ) button. The display should show INITIALIZE DISK.
4. Press the SELECT ( ) button. The printer initializes the hard disk and continues its power

Mar 12, 2008 | HP LaserJet 2420 Printer

Not finding what you are looking for?
Tektronix Phaser 740P Laser Printer Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tektronix Office Equipment & Supplies Experts

kakima

Level 3 Expert

98921 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

64286 Answers

Are you a Tektronix Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...