Question about Audio Players & Recorders

1 Answer

I have a problem with my kenwood hifi component it was PROTECT MODE pls. hepl me.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 86 Answers

1st thing. check all ur wirning from receiver to speakers, check the terminals for a wire touched the pos to the neg connecting them to gether when that dose that the system goes protect, you could check the fuses too cause it may of blown when the system went protect

Posted on Dec 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i take my Kenwood car stereo out of protect mode ?


There may be an internal short which will have to be repaired before the radio can be used.

May 25, 2016 | Kenwood Car Audio & Video

1 Answer

Hello can u help me about my MHC-gzx55d sony hifi component, when you turn on the power, the screen display appear "PROTECT" what is the problem and what is the possible damage of my component. please help...


When it goes into protect mode it has been over loaded. Remove everything from the component and unplug the unit for a minute or two. plug it back in and see if it pops out of protect mode. If this does not work then you will need to do a factory reset or check the fuses on the inside of the unit.

Feb 20, 2015 | Sony Audio Players & Recorders

1 Answer

My car kenwood says protect on the screen


That'll do it! The new speakers may have the wrong impedance to match your Kenwood. For example, if the impedance is 2 ohms or less the Kenwood may go to protect mode to prevent damage. Also, there could be a shorted wire connection which also will cause protect to be enabled. Protect mode prevents destruction of your receiver

Mar 08, 2013 | Car Audio & Video

1 Answer

My kenwood krf-v5300d overloaded? Stand by light flashes if pressed stops flashing if pressed again unit turns on but doesent pass start up and shuts off again havent managed to find a solution from bassic...


This unit is in what is called "protect" mode/ See the link below for an explanation of this. Specifically to your unit, the output components are unique to Kenwood and are not cheap. Further investigation to locate the reason for the protect mode will be necessary prior to any attempt to estimate the cost of repair. Something as simple as a missign voltage can cause this symptom.

Please feel free to update this with any other questions or concerns that you may have.

Dan

Link: http://www1.fixya.com/support/r5390728-protector_means

Oct 21, 2011 | Kenwood Audio Players & Recorders

2 Answers

My Kenwood KDC-MP142 in protect mode. is there a reset button??


My kenwood is stuck completely in protect mode. I ve everything listed and it wont come out of it. So should i assume the unit has gone bad?

Oct 20, 2011 | Kenwood KDC-MP142 Car CD/ MP3 Player

1 Answer

Kenwood KDC-MP732 CD Player in protect mode how do i get it off had a blown speaker fixed it and still in protect mode


Protect Mode (Blink): The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated.

Solution: Wire or insulate the speaker cable properly and press the reset button.

Here is a copy of the Instruction Manual for the Kenwood KDC-X790 and KDC-MP732.

Jul 25, 2010 | Kenwood KDC-MP732 CD Player

3 Answers

Kenwood car stereo cd player reads protect mode how do i fix this


i have a kenwood kdc-241 car stereo and it has gone onto protect mode i have done everything it says in the manual and even taken it out of the car just in case it was damp i have tried putting it back in but still is in protect mode can anyone help me please

May 25, 2009 | Kenwood Car Audio & Video

1 Answer

Kenwood XD V757 System Protected


check the speaker wires are not shorting out

Dec 11, 2008 | Audio Players & Recorders

1 Answer

Kenwood stereo synthesizer tuner t-85l


T-85L is a component of a hifi system not suposed to work alone. You have to connect it to another Kenwood component (an amplifier like the A85 ) through a special cable to power it on/off. The special cable can be used point to point or as daisy-chained.

Nov 05, 2008 | Yamaha HTR-5830 Receiver

6 Answers

Security Code for Protect mode


Turn on the car so the radio is flashing "Protect." Look on the front / removable face of the stereo. On it you will find a small round hole - that's a reset button. Find a small paper clip, unfold the clip and stick it gently into the hole. The "Protect" will stop flashing, and Kenwood will be displayed. Unfortunately all your settings/presets will be gone, but at least the stereo is working again!

Apr 30, 2008 | Kenwood KDC-W3534A CD Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

4804 Answers

The Knight
The Knight

Level 3 Expert

72271 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...