Question about Flat Panel Televisions

1 Answer

21 pin not working

Any one answer me my tv all21pin scart not working

Posted by on

  • 1 more comment 
  • liaqatali066 Dec 06, 2008

    Hi i have philips 32 inch wide screen tv tv working ok i have problem 21 pin scart both of them no working with aney equipment please tell me what is fault in the tv model 32dw6557/05 made from france

  • liaqatali066 Dec 20, 2008

    hi i have philips tv wide screen that all 21 pin socket not working only audio sound ok but not picture on the screen and not working on wide screen or super wide or 16.9 please tel the problem

  • Chrisry696 May 11, 2010

    Could you try typing that one more time please? Proof-read what you write.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Did it ever work? Was it working and then stop working? Did you push the correct input on remote. The problem could be the board inside t.v. In U.S.A. we don't have that on our teleivisions and I don't have any diagrams for euopia sets. Sorry can't be more help. Are you French? Always try to give as much information as possable when posting. Good-luck, If not a setting with remote, or bad cable, try unpluging power for 5 minutes. If still not working, problem inside T.V. is my best guess. Good-Day.

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv no sound and making a knocking noise after putting a scart lead in and then out again


Could you see any bent pins on the scart connector? By applying undue force, the pins can get sometimes bent and touch some other on its side.

Aug 19, 2012 | Flat Panel Televisions

1 Answer

HOW I CAN HAVE OUTPUT FRO AUDIO LINE ROM LG 55LH5000???


Hi, sorry but Most LG's no longer have audio outputs. The easiest way to get it ,You need to take the audio output from the source i.e. "cable box output"..if you have of course...
However whether your TV has this output or not we need to make some tests..5 different connections possibilities provided below.
(not by priority..you can start with any of it ).Below ,there is a sample TV back panel picture as well
Possible CONNECTIONS:
1) 2x RCA ports red / white is audio out ( L + R ) of TV to Stereo..
2) You can get also the audio digital output from the TV to a A/V receiver. the tv's optical audio out is stereo only mainly designed for freeview or tv audio to be output,
set the audio ouput on the TV menu to Dolby Digital, connect a digital optical out directly to the A/V receiver to receive audio signals.
3) since your TV has :2 x HDMI, SCART, AV, Component Video, VGA-sub, USB 2.0, connections,you may use the SCART plug to get Audio output for your TV .
TV's SCART connector which has 21 pins and "2x Audio Output " pins should be in it.
you need to buy an adapter called " RGB Scart Male to 3 RCA AV Female Adapter Converter" that can easily be found any electronic Market..one example as found eBay URL is below..
http://cgi.ebay.com/RGB-Scart-Male-3-RCA-AV-Female-Adapter-Converter-/130389078197
After you get this adapter,you need to carry the audio signal from SCART's RCA plugs to your Receiver with a 2x RCA (white/red ) cable.(if this does not work ,mfg should state somewhere in the manual..as your TV's "SCART socket IN only" ) if you properly connect IN/OUT plugs you will able to get the audio signal of the TV thru stereo..I recommend 2 $ value "RGB-Scart-Male-3-RCA-AV-Female-Adapter-Converter" with IN/OUT switch on it.
4) use HDMI connection of TV if you have HDMI input on your stereo of course...
5) if these are not an audio-out on one of these connectors , so you'll need to use the headphone socket if you want to plug it into a stereo. you need a cable 2x RCA to 3.5mm Headphone jack.
( This is the last ditch solution , since it mutes the whole sound.) ..
NOTE: if you connect this, pls be careful,your TV voice level will drive the stereo volume....

Hope this helps!..if more help requires Would you please let me know the result ?
Take care and please
Remember to rate/vote and give me 4 Thumbs Up for us
to continue f
or Helping out the Community :)


kerguney.jpg
moz-screenshot.pngmoz-screenshot-1.png

Jul 09, 2011 | Flat Panel Televisions

1 Answer

Hi i have an old bush crt 32 tv .the only buttons on the front is the vol & chan. the remote isnt working can i change to av


Hi
If your external equ is connected with a full 21 pin scart lead, to a A/V socket switching the external equ on off should tell the tv to sw to a-v . when external unit is switched off tv will return to tv ch,s . Hope this will help regards windyhouse

Jun 01, 2011 | Flat Panel Televisions

1 Answer

How do we hook up a Wii to the Sanyo DP42740 TV?


Hi Amy,

I cant see any specific connections for your tv but the end of the cable from your wii will have either a 21 pin sc"scart" connection or 3 plugs,(red, white and yellow) Look about on the back of the tv for corresponding socket. There should only be a couple of choices for each. Then simply plug it in. There will be no tuning or anything to do as these are direct connections. On your tv remote look for a button which will display or select the direct inputs. May look like a small screen shape with an arrow pointing into it, or may say "ext" or similar.
Hope this has been helpful

May 07, 2011 | Sanyo Flat Panel Televisions

1 Answer

What cable do I need to set up the HD and where do I plug it in? All the ones I lookes at have a rectangular end and I don't see one on the like that on the TV. I am using the 2 scart sockets for cable...


Any of these will work.

ANTENNA IN: UHF/VHF 75 ohm Din type (If in HD Broadcast)
EXT 1: SCART (AV Input/Output, RGB Input, TV Output)
EXT 2: SCART (AV Input/Output, Y/C Input, AV Link)
EXT 3: S-VIDEO (Y/C Input), RCA pin (AV Input)
EXT 4: RCA pin (Vomponant Input)
PC INPUT: D-sub 15 pin (ANALOG RGB), 3.5mm Javk (Audio Input)

Service Manual can be found here: http://www.givemefile.net/smanuals/lcd_tvs/sharp/file/45437.html

Feb 06, 2011 | Sharp Aquos LC-26GA5E 26 in. HDTV-Ready...

1 Answer

HAVE A MEGALOOP+ hearing aid SYSTEM. THE SOUND FROM A NEW DIGITAL TV IS DISTORTED CAN I ALSO PLUG IN A MICROPHONE TO USE WITH THE NORMAL SCART ATTATCHMENT IF SO WIRING INSTRUCTION PLEASE


I would imagine the level is too high. Does your loop amplifier not have a sensitivity control?
You could come out of the scart socket but check for a headphone volume control first!

The connection standard requires that the pins are utilised in the following manner:


Hope this is useful.

scart.gif PIN USE LEVEL / IMPEDANCE 1 Audio Output (R) 0.5V / 1K-ohm 2 Audio Input (R) 0.5V / 10K-ohm 3 Audio Output (L) 0.5V / 1K-ohm 4 Audio Ground -------------------- 5 Blue Ground -------------------- 6 Audio Input (L) 0.5V / 10K-ohm 7 Blue 0.7Vp-p / 75ohm 8 Status (CVBS) L:0-2V H:10 - 12V / 10K-ohm 9 Green Ground -------------------- 10 Data D2B (Inverted) -------------------- 11 Green 0.7Vp-p / 75 ohm 12 Data D2B -------------------- 13 Red Ground -------------------- 14 D2B Ground -------------------- 15 Red 0.7Vp-p / 75 ohm 16 RGB Status/Fast Blanking L:0-0.4V H:1-3V / 75 ohm 17 CVBS Video Ground -------------------- 18 RGB Status Ground -------------------- 19 Composite Video Output 1V / 75 ohm 20 Composite Video Input 1V / 75 ohm 21 Case Shield ---------------------

A 21 pin SCART cable with all pins connected is wired as per the following diagram:

Jan 23, 2011 | Flat Panel Televisions

1 Answer

New toshiba tv connect to sky plus box and perfect picture but no sound


Hi,

The first thing to do is check the connections between the Sky box and the TV. If you are using a SCART cable, it's possible that one of the pins in the SCART plugs has bent or become detached from the wire inside. If you have another SCART cable from a VCR or DVD player, try switching them over.

If this doesn't work, or if you are using another connection method between the Sky box and the TV, please post back and I will try to assist you further.

Regards,
BElectric

Nov 29, 2010 | Toshiba Flat Panel Televisions

1 Answer

Background telly noise


This is a very common problem caused by poor design of the SCART system which allows cross-channel feedback.

At the TV rental company I worked for we cured it by supplying "cut" SCART leads; usually these leads are completely reversible, but on a cut lead one end is designated only for the TV.

They are commercially available and easily identifiable as one plug will be labelled "TV" and the other as "video" or you can make your own using one of the generic cheap SCART leads which allow you to open the SCART plugs to access the wires:-

Open the plug and identify pin 20. They will have moulded numbers, but pin 20 is the one which is in the angled corner of the plug. The wire should usually be pink, if it is green then check pin 19 which is directly above pin 20. If this wire is pink then cut it. If the pink wire was on 20 then label the plug as being for video/Sky, and if it was on 19 then it's must be labelled for TV. Now do the other plug, whatever the order of the pink and green wires on pins 19 and 20 was on the first plug will be reversed. Cut the pink wire again. If the colours don't match then just cut the wire from pin 20 (video/Sky) at one end and from pin 19 (TV) at the other end.

Reassemble everything and plug it all in correctly and your problem should be fixed.

On a slightly different matter, never waste money on over-expensive "upgraded" SCART leads. They may look good but you're just flushing money down the toilet.

I hope that this has solved your problem, all that I ask in return is for you to take a moment to rate my answer.

Feb 14, 2010 | LG 42LC2D 42 in. LCD HDTV

1 Answer

Bought a new 42' flat - "No Program or Weak Signal"


Hi,you have not said weather you are using a scart lead(euro connecter)or an RF lead,if you are using the later don't,please connect the vcr to the tv via the scart to scart euro connecters,use a good quality scart lead(the thicker the better)as the thicker ones generally are 21 pins connected meaning it should be auto switching so as soon as you play a tape it will come straight on.

Feb 02, 2008 | Flat Panel Televisions

Not finding what you are looking for?
Flat Panel Televisions Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

68157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...