Question about Epson Stylus 2200 InkJet Photo Printer

2 Answers

Epson 2200 ink replacement light stays on

I have the Epson 2200 and the light black ink light stays on even after replacing it with two different cartridges. Any suggestions?

Thanks,

Eric

Posted by on

  • 1 more comment 
  • erictoddgall Dec 05, 2008

    Thanks for the suggegtion but this did not resolve the issue. Still have the light on over the light black ink tank.

  • todd768 Dec 17, 2008

    Same deal... light stays on after 2 new tank replacements

  • llamacide Dec 18, 2008

    mine just did this today too!!! WTF?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem with the light black and light magenta as well. It took trying only one new cartridge with the light magenta before it worked.
The light black took 4 new cartridges before it worked. I had called the Epson support center on this problem and after going through suggestions they made that did not work, I told the guy I had another new cartridge on hand. He said to go ahead and try it. This time the printer worked. He took my name and address and said the other cartridges were faulty. Epson is sending me new replacement cartridges at no charge.

Posted on Feb 06, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Epson Master
  • 541 Answers

This means that your printer wast pad is full this now you reset your printer but make sure you have put new pads in 1st

  1. Turn off the printer power and unplug the power cord from the wall. Disconnect the computer interface cable at the back of the printer.
  2. After one minute reattach the power plug to the wall, but don’t reattach the computer cable.
  3. Hold down the ROLL and the PAPER ADVANCE buttons simultaneously.
  4. Turn the printer on. after 2 blinks, all the ink lights come on, then release the buttons being held down.
  5. Press and hold the ROLL button for 10 seconds.
  6. Release the ROLL button and the printer will initialize, which resets the Waste Ink Pad Counter.
  7. Once initialization is complete, turn the printer power off.
  8. Reconnect the interface cable.
  9. Turn the printer on and print a document.

Posted on Dec 04, 2008

  • Lee Reynolds
    Lee Reynolds Dec 08, 2008

    try download the ssc put that in google

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find ink supply level on epson 2200 ink


Open the Epson Printer Utility, Click on the printer name if you have more than one printer then OK. Click on Epson Status Monitor at top. A dialog box will come up telling you if any ink needs to be replaced. Click on the OK button in this box and this will take you to another dialog box which will show you the amount of ink left for each color.

Mar 22, 2010 | Epson Stylus 2200 InkJet Photo Printer

2 Answers

How do you change the black cartridge in the printer epson stylus nx115


Here is the Link showing instructions below. If you find this helpful, pls rate me.

http://files.support.epson.com/htmldocs/nx110_/nx110_ug/wwhelp/wwhimpl/js/html/wwhelp.htm

Replace Ink Cartridges
Your Epson Stylus NX110 Series and its software will let you know when an ink cartridge is low or expended.
If ink is low, the ink light flashes. You can continue printing until a cartridge needs replacement.
If a cartridge is expended, the ink light stays on. You must replace the cartridge to be able to print.

Warning:
Keep ink cartridges out of the reach of children and do not drink the ink.
Note:
If you need to change a cartridge before it or any other cartridges are low or expended, run the Ink Cartridge Replacement utility.

You cannot print or copy when an ink cartridge is expended even if the other cartridges are not expended. Replace any expended cartridges before printing or copying.

Leave your old cartridges in the Epson Stylus NX110 Series until you are ready to
replace them to prevent the print head nozzles from drying out.
When an installed ink cartridge is more than six months old, you may need to replace it if your printouts do not look their best, even after cleaning and aligning the print head.
Follow the instructions in these sections to check and replace your ink cartridges:
Check Cartridge Status
Purchase Epson Cartridges
Replace Cartridges Using a Printer Software Utility
Remove and Install Cartridges

pls rate me. Thanks and Good Luck...

Jan 23, 2010 | Epson Stylus NX115 All-In-One InkJet...

2 Answers

Printer will not recognize a new full cartridge of ink


See the HP web site http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&cc=us&docname=c00489814&dlc=en for resolve.

Apr 28, 2009 | Epson Stylus 2200 InkJet Photo Printer

1 Answer

Epson 830u Printer Red light stays on even with new ink


I realised that I had to replace both the ink cartridges even though I only wanted to replace the black for it to work. Once I replaced both the black and colour cartridge the red light went off. Thanks

Feb 11, 2009 | Epson Stylus 830U InkJet Photo Printer

1 Answer

Ink was low I put a new cartridge in still says low wont print.


Hi

try reinstalling the ink. if all fails call epson for replacement ink at 562 276 1300

Jan 02, 2009 | Epson Stylus 2200 InkJet Photo Printer

1 Answer

Epson 2200 printer ink pads


First download this Epson utility to reset the ink counter:
http://inkjetprinterhelp.us/epsonSSC.html

Read the disassemble instructions on this link:
http://www.fixyourownprinter.com/forums/inkjet/35177

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Dec 27, 2008 | Epson Stylus 2200 InkJet Photo Printer

1 Answer

Light purple cast to black and white prints


Known issue. Use QTR to print bw prints. Works great on my Epson 2200.
http://www.quadtonerip.com/html/QTRoverview.html

Dec 06, 2008 | Epson Stylus 2200 InkJet Photo Printer

1 Answer

EPSON 2200 - Waste Ink Pad Replacement


You can replace the pads yourself.... I wouldn't really mess with it though. There are other ways Google search "Waste Ink Epson 2200" to see how to setup an external tank.. I have mine setup this way and its been no problem.... If you're set on taking them out remove the screws from the sides and middle and the bottom will drop away and reveal the pads.


Mar 25, 2008 | Epson Stylus 2200 InkJet Photo Printer

2 Answers

2200 locked up


disconnect the printer from the computer - power off printer - check for obstructions / torn papers - power on

if paper light is still on/flashing and pressing it does not do anything - you got a hardware issue - call manufacturer for reccomendation

this might help also - http://www.epson.com/loyalty

Dec 23, 2007 | Epson Stylus 2200 InkJet Photo Printer

1 Answer

Ink light on


you must verify all lefvels of yopur ink cartrages some of the others maybe low

Sep 04, 2007 | Epson Stylus CX3810 All-In-One InkJet...

Not finding what you are looking for?
Epson Stylus 2200 InkJet Photo Printer Logo

649 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Cindy Wells

Level 3 Expert

4758 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...