Question about Air Hammers

Open Question

Please send me instruction booklet on the below.

I have misplaced my instruction booklet on my Farberware stand cake mixer. 16 speed.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix the knock sensor on my 2003 Saturn Ion 1


The knock sensor is located just below the throttle body.It has a single wire going to it.

Jul 26, 2014 | Standard Ignition Knock Detonation Sensor...

1 Answer

How to locate the knock sensor on a 2003 Saturn Ion?


The knock sensor is located just below the throttle body.It has a single wire going to it.

Jul 26, 2014 | Standard Ignition Knock Detonation Sensor...

1 Answer

Dewalt corless nailer lost power while puting nails in wood, he is working but does not have power to go all the way in the wood


Have you been keeping the gun properly lubricated? In the high dust atmosphere of the workplace it needs cleaned & lubed frequently.
murf427

Aug 01, 2012 | Dewalt DC618K - 18V, 16 Gauge, 20 Degree...

1 Answer

DONT TURN ON


Typical cause for failure to turn are 1) The power cord has an open/broken wire. Check with an Ohm meter from the plug up to the trigger switch. You should see zero Ohms on both sides of the line between one plug spade and one side of the switch, then the check the other side. 2) The switch is bad. Check that you have zero Ohms across both sides of the switch when the trigger is pulled. 3) Brushes are worn down too far. You should see continuity from one brush to the other, that is see some resistance through the armature coil. All these measurements must be done with the drill NOT plugged in.

Jun 29, 2011 | Makita 1 - 9/16" Sds - Max Rotary Hammer...

1 Answer

I have a makita Hammer drill # 6914D model 527047E looks like it is need of some oil what kind. The glass window is empty can you help me tried to find a manual but cannot.


Go to the below site for a manual. There isn't any reference to a glass window in the manual but the tool does need to be regreased as indicated in the manual, especially if it's used frequently. If you do it yourself, pay close attention to how much grease you put in the tool. Too much grease causes excessive drag and makes the motor work harder.

You can find an owner's manual and parts breakdown on Makita's website: http://www.makitatools.com/en-us/Modules/Tools/ToolDetails.aspx?ID=173.

Apr 26, 2011 | Makita HK1810 Power Scraper, Small,...

2 Answers

We are using three screw oil free atlas copco compressors{ZR-275}. They often encounters the problem of high outlet temperature of first stage , almost near tripping stage. and we have to replace the...


Dear Hamza,
High Temperature at First Stage means your Second stage is becoming Weak and it is not capable to pull the maximum air from First stage, If it is only at loaded position.
If this is your regular problem you must check your Water condition it should not be below 20 degree C and not above 40 degree C.
You may also try to blow some dry air into second stage ( HP Element ) when ever it is in off position.
Hope this will help you.
Regards
Ashfaq

May 21, 2010 | Atlas Translator Atlas Copco Air Hammer...

1 Answer

Hardwood Floor Repair.


take a damp washcloth and a steam iron

put the damp washcloth over the dent and iron the dent with the steam iron

that should slowly raise the grain

be careful not to get the iron too hot where you scorch the floor

and work slowly, don't get in a hurry

Jan 02, 2010 | Farberware Manual Hardwood Flooring Nailer...

1 Answer

Floor nailer, 2" nail not going into harwood


sounds like a bent shaft has the driver had any nail stuck or came out the side? whats the presser on?Are you nailing over exiting floor such as v.c.t or other hardwood floor try a couple drops oil in the nailer i' ve been doing floors for over 30 years these are some of the problems i came across hope its helps some what

Dec 23, 2008 | Farberware Manual Hardwood Flooring Nailer...

Not finding what you are looking for?
Air Hammers Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Hammers Experts

John Trevino

Level 3 Expert

1378 Answers

Daniel McLaughlin
Daniel McLaughlin

Level 1 Expert

14 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Air Hammer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...