Question about Dell Televison & Video

1 Answer

52" plasma tv - turns on - and I hear something reset inside

This just happened last night - the tv was working fine and then all of a sudden I hear a click and no picture. I can turn the tv on and then I hear something inside of it reset with a clicking sound - and now no picture to the tv even though I know it's on. It is a 52" dell plasma

Is there something inside of it resetting itself?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I hear a clicking noise- the clicking noise is most likely you ballast trying to power the lamp, but failing. this may indicate a defective ballast if you have recenty purchased a new lamp.I recomend you have your lamp tested to help narrow down the cause of the defect. It's highly unlikely for a new lamp to be dead on arrival

Posted on Dec 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic Plasma 50 TH-P50U30A blacked out with no sound


Appears to be a power supply issue with everything being so dead.

Jan 22, 2017 | Panasonic Televison & Video

2 Answers

RCA D52W20 HDTV TRIES TO TURN ON 3 TIMES BUT WONT POWER UP


remove all the electrical wire connections from the back of the tv .remove the power plug from the electrical outlet and wait for two minutes and replug the wire and then ckeck.it should work.
reply.

Oct 29, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Mitsubishi WD-52525 was working fine and now it will not turn on


This is just a shot - but it worked with my Sony (same problem).
Pressed remote power on button AND held Power button on TV on at the same time.

Set clicked 4 or 5 times and then came on....

Other, most have a (VERY small) reset switch on the rear - near where the power cord enters the TV... Use a flashlight and a mirror to locate it on your set....

Nov 26, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Black 3" vertical line through the center of my Plasma TV


Sounds to me like one of the drivers for the display died. Typically this requires a replacement of the entire panel (expensive) but I'd check with your local repair shop

May 04, 2009 | Panasonic Viera TH-50PZ80U Plasma TV

2 Answers

Mitsubishi wd-65831 one night worked fine next day nothin..


If you hear a whining noise, the odds are it is the color wheel, the bearings are bad in it and will need to be replaced as a whole unit, kinda pricey, my suggestion, sale the bulb and all boards in it and which should fetch about 400+ and invest in a new TV, a color wheel is pricey unless you can find a deal

Dec 09, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

ESA 42' plasma turned off on it's own and won't turn back on.


I think, when a power supply's time is up, it's up now. There is not usually any advance warning,(besides your warranty has expired of course). If you are feeling un-normal heat from the TV, that is a sign the power board just fried out. They always get very hot, from the microchips cooking themselves until there is nothing left to need power. Plan on paying a TV tech to replace your power board.

Nov 13, 2008 | Televison & Video

2 Answers

Nakamichi vu50p Plasma TV wont turn on at all


Get a Harmony remote. Has codes for almost everything and I can verify it has codes for the vu50p

Mar 31, 2008 | Nakamichi VU50P 50 in. HD-Ready Plasma...

8 Answers

ESA 42" plasma tv not turning on


I have a 42 inch plasma and I was watching tv last night on it and suddenly it turned off on it's own. I tried turning it off and on and nothing happened. Then I tried to unplug it and replug it and nothing. My remote does not work either. Anyone know what exactly happened? Did my screen blow or what? I hardly ever use the tv and I only had it on from 8:30 p.m. - 10:20 p.m. and it turned off. All the other tv's in my house worked fine - I checked them. Also, my dvd player and cable box is on the same power cord and both of them work. Any solutions or help would be most appreciated!!! Does it just need to cool down or did I burn something out? Help!!!

Mar 16, 2008 | Hitachi 42EDT41 42 in. HD-Ready Plasma...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Televison & Video Experts

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

CoppellTVRepair.com

Level 3 Expert

749 Answers

Are you a Dell Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...