Question about Kyocera Mita FS-1030D Laser Printer

4 Answers

Can you help me with kyocera fs-1030d

Hi,

my printer kyocera fs-1030d second green light flash and 2 green and red light flash together. printer is offline. can u help me. thanks

Posted by on

  • stupidheart Dec 06, 2008

    First three lines printing is light

  • AAAA262430 Dec 16, 2011

    CHANGE THE FUSOR (CH-152-35) ES BLANCO(WHITE) , PLATEADO (??NO ENGLISH LOST MEMORY)Y (AND) BLACK (*****)
    GREEN GREEN RED RED
    NO YES NO NO
    YES YES YES NO AND REPEAT

    -------------------------
    GREEN GREEN RED RED
    YES YES YES YES
    NO NO YES NO
    CHANGE BOARD WHERE IS LPT, USB, NET

    -------------------------
    GREEN GREEN RED RED
    YES NO YES YES
    NO YES NO YES
    CHANGE BOARD WHERE IS LIGTH(GREEN GREEN RED RED)

    EXCUME WRITE, BUT I WRITE IN SPANISH.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

If a paper jam occurs while printing, the printer notifies it by the following combination of the four indicators. Remove the
jammed paper . After removal, open and close the top cover once to initialize the jam sensing

Posted on Sep 18, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 622 Answers

The second green light means printer is receiving data and the sencon red light means you are out of toner...

Posted on Dec 24, 2009

  • ashishborad Nov 27, 2010

    if tonner is empty then only second red light on..

×

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 47 Answers

CHANGE THE FUSOR (CH-152-35) ES BLANCO(WHITE) , PLATEADO (??NO ENGLISH LOST MEMORY)Y (AND) BLACK (*****)
GREEN GREEN RED RED
NO YES NO NO
YES YES YES NO AND REPEAT

-------------------------
GREEN GREEN RED RED
YES YES YES YES
NO NO YES NO
CHANGE BOARD WHERE IS LPT, USB, NET

-------------------------
GREEN GREEN RED RED
YES NO YES YES
NO YES NO YES
CHANGE BOARD WHERE IS LIGTH(GREEN GREEN RED RED)

Posted on Dec 22, 2011

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 27 Answers

You have got a printer error problem which you cannot fix yourself. you need to take it to a repair centre because there is something faulty in the printer(those lights indicate an error code).

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kyocera fs 1030d: first sequence: 1.led:green


THE PROBLEM IS THE FUSER, YOU HAVE TO OPEN THE ENTIRE TEAM AND IN THE BACK OF PART WHERE IS HEATS UP THE PAGE, BETWEEN ROLLER GREY AND ORANGE, ALLI THIS FUSER. HIM REMOVING THE ENTIRE PIECE THIS SUBJECT TO TWO SCREWS, YOU MUST DISCONNECT THE CABLES (THREE PAIRS), THE PIECE THAT YOU JUST EXTRACTED HAS TWO SCREWS THAT HOLD A BONBILLO THAT IS INSIDE THE GRAY CYLINDER, THERE BELOW YOU WILL SEE A SMALL WHITE PIECE THAT IS SUSTAINED BY TWO SCREW WHICH ARRIVE TWO CABLES, THE DRAW AND THEN TO THE WHITE PIECE WITH A FINE NEEDLE HIM GOING TO PASS UNDERNEATH AND CAREFULLY RAISE THE BLACK PARTIF THE VERIVICAS SHOULD GIVE CONTINUITY WITH EN MULTIMETRO O METER OF VOLTAGE. IF YOU WANT THE CAN BUY ALSO IN AN ELECTRONICA. SORRY ENGLISH

Aug 17, 2011 | Kyocera Mita FS-1030D Laser Printer

1 Answer

How do I check the IP addres on the 1030D printer


Hold the green button down for 3 seconds the lights willflash after 3 seconds seconds release the button then and the printer willprint a status page the network status on this

Jul 14, 2011 | Kyocera FS-1030D Laser Printer

1 Answer

Kyocera FS 1030D Flashing Lights


you are out of toner and you have a paperjam

Jun 16, 2009 | Kyocera Mita FS-1030D Laser Printer

2 Answers

Kyocera fS-920KX. Not printing


There are actually some certain meaning on the red light and green light showing different information to user. The summaries are:
1) Green On, Red Off = Printer Ready.
2) Green Fast-Flashing, Red Fast-Flashing = Printer warm up.
3) Green Fast-Flashing, Red Off = Printer off-line.
4) Green Slow-Flashing, Red Off = Processing Data.
5) Green Off, Red On = Cover Opened, Toner Empty or Developer Unit / Drum unit missing.
6) Green Off, Red Fast-Flashing = Paper Jam or waiting for jam reset.
7) Green Off, Red Slow-Flashing = Paper Empty or Paper tray is not inserted.
8) Green Off, Red Off = Printer power is off.
9) Green Very-Slow-Flashing, Red Off = Printer in sleep mode.
10) Green (any condition above), Red Slow-Flashing = Toner low or paper empty.

So what is your printer condition? Better know what is going on your printer so can solve the problem

YBC (/\)

Jun 01, 2009 | Kyocera FS-920 Laser Printer

3 Answers

How to print configuration page for a Kyocera FS1030D


Try press and hold the green button for about 10 seconds. HOPEFULLY this will cause the printer to produce a configuration page with the details. Good luck!!

Sep 25, 2008 | Kyocera Mita FS-1030D Laser Printer

2 Answers

KYOCERA FS-1030D - 3rd Light from top is Red


this is problem with cassate please add paper in cassate.
* in cassate at last one green color botton is there set that one as per paer size

* after remove the cassate see at front left down there one white color sensor is there this sensor senseing the cassate availbilty please check that one

* while inserting cassate insert slowly

Jul 06, 2008 | Kyocera Mita FS-1030D Laser Printer

2 Answers

Fs-1030


This is a Thermostate problem. You have to reset thermostate or replace the fuser unit your problem will resolve.

Jun 10, 2008 | Kyocera Mita FS-1030D Laser Printer

1 Answer

Top 3 lights blinking on printer


The flashing of the LEDs you describe indicates a error. If you call the Kyocera Help Desk they can tell you what the error is based on the order and color of the LEDs. They can be reached at 800-255-6482.

Aug 18, 2007 | Kyocera Mita FS-1030D Laser Printer

Not finding what you are looking for?
Kyocera Mita FS-1030D Laser Printer Logo

1,471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Printers & Copiers Experts

NewYork kyocera HP...

Level 3 Expert

513 Answers

Henry Gertcher

Level 2 Expert

46 Answers

Kevin Cole

Level 1 Expert

45 Answers

Are you a Kyocera Mita Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...