Question about Televison & Video

1 Answer

Convergence settings how do you set the fsctory defaults on a vs-5052?

Posted by on

  • smallblocks2 Dec 06, 2008

    now what do the abreveations mean in these meunes?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 140 Answers

With the remote control,hit the menu key and bring up the menu on screen. Then enter 2358 on the remote for the option menu,enter 2357 for the adjustment menu or 2359 for the convergence adjust menu.

Posted on Dec 04, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I reset my canon xt EOS to factory settings

To restore fsctory settings set Mode t0 P, open menu at Set Up Tools 2 and selct Clear settings. This restores factory settings but I am not sure this is the answer to your problem. There are numerous reasons your images might be soft other than incorrect settings. I would be interested to know the outcome.

Nov 13, 2011 | Canon Rebel XT / EOS 350D Digital Camera

2 Answers

My Mitsubishi vs 50607 has blue green and red lines jumping all over the screen what is the problem and fix

You have some bad filter caps in the convergence section of your set or a bad convergence chip

Aug 05, 2010 | Mitsubishi VS-50607 50" Rear Projection...

1 Answer

Mitsubishi VS-50805 HD 1080 Series

check the convergence ic's unplug the main convergence board plug then try the set again if the set comes on get a convergence kit here

May 16, 2010 | Televison & Video

1 Answer

Mitsubishi vs 5052 has no picture

There seems to be a lot of people having problems with this TV. My TV is doing it too. If you find out the answer, can you email me please?

Oct 17, 2009 | Televison & Video

1 Answer

Convergence problem

I have a VS-45607 and If the VS-5052 has the same menus then there are two options for convergence. One is the basic convergence where there is one set of crosshairs and you line them up. Then there should be an option for "advanced" calibration where the whole screen looks like a grid and you go to un-converged crosshairs and align the screen. Most likely not all of them will need to be adjusted, but for me, the lower right hand corner wasn't aligned right and this cleared it right up.Good luck

Dec 03, 2008 | Mitsubishi VS-45607 45" Rear Projection...

1 Answer

Blue color lamp cannot converge


Nov 30, 2007 | Mitsubishi VS-55601 55" Rear Projection...

1 Answer

Mitsubishi 50 in vs-5043

Needs convergence circuit O/h==replace convergence IC's & any damaged/over-heated as needed.

Oct 01, 2007 | Mitsubishi VS-50502 50" Rear Projection...

1 Answer

Mitsubishi vs-4543

Most likely the convergence output IC has shorted out and has overloaded the convergence power supply, which has stopped working. The computer senses that the convergence power supply is not running and shuts the set down. The convergence IC should be replaced, the power supply restored and the convergence circuits realigned by someone experienced in Mitsubishi projection sets. When I do a housecall for a set like that I charge $150, but shops in your area will vary so ask around.

Aug 04, 2007 | Mitsubishi VS-4543 45" TV

1 Answer

Convergence board

It wouldn't be the entire convergence board, you more than likely have a bad convergence STK-IC. Replacing the IC will take a good bit of knowledge and training as far as electronic repair is concerned, plus a complete convergence set up. In other words, unless your certified, you need to contact a tech. The convergence set up alone has driven men to drink.....

Aug 28, 2006 | Mitsubishi VS-45609 TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74990 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5297 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides