Question about Indesit W 123 Front Load Washer

1 Answer

Indesit wm2x front dial just keeps clicking round when trying to put a wash on to start

Posted by on

  • sean7455 Dec 09, 2008

    cheers for that it worked :-)

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

We had similar fault.
Rectified ours by switching off at the mains and put dial to one of the dots. Switched on and it reset.
Good luck

Posted on Dec 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit w83 dial just clicks round, is there a reset button some where


Washed any coins lately? I had a front loading washer and when mine did that it was still under warranty so the service came out and pulled a quarter out of the drain trap. If you not sure where that is contact me

Dec 20, 2013 | Indesit W 83

1 Answer

I have a indesit w123 and when i put it on it starts to fill up and then the dial keeps going round, can you help please...


try and clear prog memory .what to do is set prog knob to an off position where the black spot is then switch on machine the red light will flash quickly then slow down. when it does switch machine off then select program and switch on and it should be ok.if not it could well be a main fault on pcb .indesit boards are not very good .hope this helps.

Jun 07, 2011 | Indesit W 123 Front Load Washer

1 Answer

Indesit programmer has a mind of its own


I have LG Washing Machine WF-S6607 when I START after 5 Second it will be stop and alarm to come up on Rinse MODE. what I do?

Oct 17, 2009 | Washing Machines

1 Answer

Indesit wm 12x


Sounds like the pump is blocked. Lost a sock lately?

Mar 13, 2009 | Indesit WA 115 Front Load Washer

1 Answer

Dial keeps rotating


This a common problem with Indesit washers..
It is not a timer but a programme selector switch.
What you need to do is the following.
Switch the m/c on, let the drain pump empty the water, then switch the m/c off.
set the selector switch to one of the black dots on the dial, which is stop/reset.
Then switch washer back on, if the dial still keeps going round and round, then you are going to have to call an engineer, as you have what is called an Anomaly (fault).
Plz leave feedback for this solution.
Thanks

Dec 09, 2008 | Indesit W 123 Front Load Washer

2 Answers

Indesit w1 13 reset


If your washer has some black spots on timer dial then set your dial pointer to one of these spots to reset programme.

Then try it again, if it still does the same thing, then you probably have a faulty control module.
Expensive!!!!!

Nov 06, 2008 | Indesit WA 115 Front Load Washer

1 Answer

Indesit W123 5 flashes error!!


The F05 fault means the pump is blocked, check the filter at the front bottom right of the machine behind the plinth and if its connected under a sink check the hose & connection

Nov 03, 2008 | Indesit W 123 Front Load Washer

1 Answer

INDESIT WI101


hiya
these machines will do this if the timer dial has been moved during a cycle, they have a memory chip on the main circuit board.

they also do this if the machine has a fault with the exception that they dont stop, the doorlock light flashes and the timer just keeps clicking.

try setting the timer to a dot on the settings then switching the power on, the doorlock light will flash a few times, turn off again select program then switch back on, machine should now be reset and work ok, if not then count the flashes of the doorlock light as this indicates a fault code.

hope this helps


please dont forget to rate the helpfulness of this reply thanks kj

Aug 04, 2008 | Indesit W 123 Front Load Washer

1 Answer

My indesit washer/dryer model w10 ,is not working.the programme dial keeps cliking round wont start a programme or take in water.


probably a main module fault but worth while checking for continuity thro the heater and that the pump and filter are ok. the idea is that when a fault is detected, the dial will click round indicating a fault but usually it is the module itself. expensive part. not worth repair

Jul 04, 2008 | Indesit Washing Machines

2 Answers

Indesit w143uk


these machines are a problem! the dial clicking round can be a component fault - ie pump etc - or a module fault. from what you describe, fault could be with the pump. an easy way to check is to power the pump up independently and see if drain works ok. (i assume you have checked the filter) after that, check continuity in the heater as well. if both of these are ok, you are faced with a module fault

Jul 21, 2007 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

neilmoto

Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...