Question about LG WM-2277HW Front Load Washer

1 Answer

Once I turn on the machine, I hear the "on" beeps but no lights on the controls and no display either.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 240 Answers

If yours has the control board mounted in back of machine, is there a red led lit on it? this indicates operation of main board. if lit then replace user interface.

Posted on Dec 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gwl 11 wont rinse or spin


(00000101) Phase 1 - Communications Fault
The Display Module has had difficulty communicating with the Motor Controller.
Primary Source: Display Module.
Action: Turn off at the wall and on again after 5 seconds and try again.
1. Undo 2 screws at the back
Check connections of the 12 way harness for bad contacts,
corrosion etc.
2. Check for moisture in the console area. Dry out if necessary
2. If still faulty, replace the Display Module
3. If still faulty, replace the Motor Controller. If the new Motor
Controller corrects the fault, then refit the original Motor Controller.

Oct 11, 2014 | Fisher and Paykel Washing Machines

1 Answer

Control light is on... stuck on drain with 11minutes remaining


with machine on,push and hold any two buttons until you hear a beep,or for at least 30 secounds machine should now be reset.adrian

Jun 07, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Code in digital display does not have a E in front of it


Please let me know if you can get a number after this - if so what number shows up?


Model differences:
• Better models have a digital readout display
• Good models do not have a digital readout display
In the Better Models line, the failure codes will appear in the display as an E followed by two numbers, a number and a letter
or two letters. The control will beep and the Door Lock, Wash, Rinse, Final Spin and Control indicator lights will flash.
Example: E14. To stop the flashing and beeping, the customer may touch the Pause Cancel button. The error code remains
stored in the control but once the problem is corrected, it does not effect the operation of the washer. If the failure is something
that the customer can correct (such as the water faucets being turned off), the washer will operate normally the next time it is
started.
In the Good Models line, the control signals the failure code by flashing the five indicator lights of Door Lock, Wash, Rinse,
Final Spin and Control for the first number or letter after the E and the Start indicator light for the second number or letter
after the E. When a failure occurs, the washer stops or pauses and the control beeps and flashes the five indicator lights to tell
the customer that a failure has occurred. To stop the flashing and beeping, the customer may touch the Pause Cancel button.
The error code remains stored in the control but once the problem is corrected, it does not effect the operation of the washer.
If the failure is something that the customer can correct (such as the water faucets being turned off), the washer will operate
normally the next time it is started.
To recall an error code,
• Wake the machine by pressing any button
• Wait 5 seconds
• Press and hold the Start and Pause Cancel buttons simultaneously
• All LEDs will go blank and after a few seconds the control will signal the stored code using audible beeps and blinking
LEDs. The control will repeatedly signal the code, as long as the Start and Pause Cancel buttons are pressed.
A two-second pause between repeats affords you the ability to make accurate counts to identify the correct error codes.
Please Note the following...... on a small number of washers with serial number prefix XC4,
if the previous procedure does not perform as specified, follow the option below:
• Follow all previous steps but instead of pressing Start and Pause Cancel buttons,
press and hold Options and Pause Cancel buttons.
If the washer is a Better Model, the error code will appear in the display. Troubleshoot problem by using charts on the
following pages.
If the washer is a Good Model, the five indicator lights of Door Lock, Wash, Rinse, Final Spin and Control will flash the
number of times for the first digit of the code and the Start indicator light will flash the number of times for the second digit.
Take
separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code.
The code is obtained by counting the number of times the lights flash. Example E24: The five indicator lights would flash twice
indicating the 2 and the START indicator light will flash four times indicating the 4. The five indicator lights and the START
indicator light start flashing at the same time.
The control will pause for 2 seconds, then repeat the code as long as the two buttons are pressed and held.
Note: A letter appearing in the code stands for a number higher than nine:
A = 10 B = 11 C = 12 D = 13 E = 14 F = 15
Example Code F1: the first digit would be 15 and the second digit would be 1. If this code would appear on a washer in the
Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once.

May 13, 2014 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Fisher & Paykal MW512 turns on multiple beeps then turns off


This kind of problem is usually related to a faulty display module, or faulty motor control module (Computer isnide of control panel compartment)

Without spares to change and test with, you wont be able to diagnose 100%

Usually when there is a problem, a series of lights go solid on the control panel and the machine beeps to alert you to a problem and this is a fault code, but if nothing is showing at all, then I have to lean towards the display module underneath the touchpad. Especially considering it wont illuminate.

Nov 22, 2012 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Just moved front load beaumark washer into a new house, and it won't fill with water. the display lights up and you can here washer trying to fill (humming noice). All display lights come on and it...


It sounds like your water inlet valve is either not getting a signal to let water in from your control board or the water inlet valve is defective. Since you are hearing a humming noise, I would say that the water inlet valve is defective or has been damaged in transit.

Jun 18, 2011 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Drain pump and motor control board was replaced. Entered the load size and when to start the machine and the display lights went out. Unable to do anything with the display panel now. I have power at...


Hi just read your posting.Sorry to ask these questions but why did you replace the control module and pump?When you turn the power off then on at the wall does your machine light up the display and give a beep as well? Did you hear a popping sound when you tried to use the machine?Did you smell anything burning?Please reply with additional information and I am sure I can help you.Looking forward to your reply.

Sep 20, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Hi I have a GW708U Model. The lights on the display panel come on and then nothing happens when you hit the Start button. Any suggestions welcome.


Hi just read your posting.Just a couple of questions, Do you hear a beep when you push the start button?IF you don't then the problem is your display board.If you hear a beep and it does not start then the problem could be your lid switch.How old is your machine?Please reply with more information and I can help you track this problem and repair it.

Jun 06, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Fisher and paykel smart drive 703 top loader, lights go on but pressing them even to start does nothing not start or let me change the size of the load ;(


Hi, just read your posting.Now the possible fault could be your display board.When you turn the power on to the machine from the power point do all the lights come on and you hear an audio beep beep , then the lights go out ?If that happens, then do you push start and can not select anything else like water temp or load size?Or do a series of lights light up and it beeps indicating a fault code after you have pushed the power button? Please reply and I can guide you throe step by step the process needed to fix this problem.

Jun 05, 2010 | Washing Machines

2 Answers

The lights come on, but the machine doesn't start


do you hear a beep when the start button is pushed? if u do hear a beep then it could be your lid switch is faulty, if you dont hear a beep then your keypad is faulty. is the plastic covering the buttons cracked?the keypads fault sometimes because water goes thru the cracks into the electronics causing it to corrode. please reply with answers 4 more help.

May 06, 2010 | Fisher and Paykel GWL11 Top Load Washer

4 Answers

How do i change the language on my washing


Press and hold the drying,delay start/temp select buttons altogether for 5 sec untill you hear a beep, then release all 3. press the dely start button to scroll through the available languages then select your chosen language by pressing the drying button once.

Apr 07, 2010 | Hotpoint Ultima WD72 Front Load...

Not finding what you are looking for?
LG WM-2277HW Front Load Washer Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...