An expert who has achieved level 3 by getting 1000 points
Superstar:
An expert that got 20 achievements.
All-Star:
An expert that got 10 achievements.
MVP:
An expert that got 5 achievements.
Office Equip... Master
6,674 Answers
Re: Error Code C-0010
Without the Bizhub model number. You mite try this, take each of the image units out and shake them so that all of the developer and toner are spead out across the entire image unit one of the image units mite have been stored with all of the developer at one end, and when place in the machine the motor for that image unit has a hard time trying to turn..
Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi there, the error code 7401 means that there is a problem with the toner sensor in the black developer unit (see service manual page 1-4-15), replace the black developer unit and the problem will be solved.
Black drum ATDC replace the black developer unit, also check to make sure the black toner is getting into the black developer unit. Open close the front door to reset the code (Not the Toner door)
e000020 is error with toner unit, several possibility : - The toner is empty - The developer failsto be replenished with starter developer properly. - Related developing unit - Ahopper motor error is identified by the detail code of E020. However, it may be identified by E02x according to need.
The 7410 indicates a drum error (see below) the 0163053 is the number of prints made by the printer. The drum was most likely knocked loose when installing toner. Drum unit non- installing error - The drum unit is not installed or not installed properly. Detaching and refitting the developer unit Procedure 1. Open the top cover. 2. Open the MP tray. 3. Remove the developer unit. 4. Check or replace the developer unit and refit all the removed parts. Detaching and refitting the drum unit 1. Remove the developer unit. 2. Open the left side cover and then remove the waste toner box. 3. Unlock the drum unit lock and then remove the drum unit. 4. Check or replace the drum unit and refit all the removed parts. I hope this is helpful, Shawn
c380 indicates auto-toner error for black developer (K).
Check following:
Is the harness between the LGC board and the developer unit drawer connector open-circuited? Is any harness inside the developer unit or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector CN341 on the LGC board disconnected?
IF connector no problems, then u probably need to replace the auto toner sensor.
e0020 is to do with there not being enough toner in the developer unit.
Firstly it may be a good idea to check/change to toner cartridge.
Switch off and disconnect from mains for the next bit.....
If ok remove the developer roller, cover is above the manual tray on the right hand side then once inside dev unit has connectors at either side, check they are properly seated. If you need to remove the dev there are several black screws around a metal plate all need removing. The roller should be black with toner. May need replacing depending on age and usage of copier.
9-357. Black toner problem.Probably You have low toner sensor defect. But try first to vacuum and clean black toner dispenser.You must vacuum whole path wich is used to transport black toner to developer unit.Then if printing B/W print only, you must print 10 full color sheets every 100 copies.
what model machine?
×