Question about Necchi 3537 Mechanical Sewing Machine

1 Answer

Bobbin case on my 524fb necchi has come apart

The bobbin case on my 524fb necchi has come apart and will not hold the bobbin in place

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Almost all Necchi use a class 15 bobbin & bobbin case, a new case should cost around 7 to 10 dollars!


Posted on Mar 14, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sewing machine belt for necchi 524FB

Check with a sewing machine repair shop. Bring the old belt with you, if possible. Otherwise, be sure to have the make & model number with you.

Jan 26, 2017 | Necchi Sewing Machines

2 Answers

Necchi 3537 manual is useless. How do I put bobbin shuttle hook back into the machine?

HINT: before you install the shuttle, make sure to place a drop of sewing machine oil around the outer edge of the shuttle and lightly spread it around the outer edge (you should do this about every time you change a bobbin). Sorry, you'll probably need to be familiar with removing and installing the shuttle. Have patience! Once you've done it a couple of times, you'll wonder why it was so difficult.

It usually helps if you can tilt the machine back about 45 degrees so it is supported by something (pillow, cushion) so you can get good visibility into the bobbin area.

Raise the needle so that the take-up bar is at its highest point.

Make sure the outer hinged door on the shuttle area is open. Inside that open door is a metal unit that is shaped like a "C". The shuttle makes up the other part of the "C". The two C's face each other and complete the circle. Grasp the shuttle by the projecting bobbin pin. (Perhaps the photo & videos will help you in placing the shuttle (you'll probably need to wiggle it around a little until it pops into place.) Once the shuttle has snapped into place and you've closed and latched the outer cover, you can install the bobbin case.


Necchi Zig Zag Shuttle movement

Necchi Oscillating Shuttle

Jan 04, 2016 | Necchi Sewing Machines

1 Answer

I have a Necchi 4900 and the thread catches on the bobbin holder , moves the bobbin holder out of place , james , have taken it out cleaned everthing under the bobbin and takewn the underneath cover

try changing the needle to see if that helps
if it doesn't,, then I suggest that the sewing machine be checked
at a repair shop to see if the bobbin case needs to be replaced and
to see if the hook and the hook race need to be replaced

Nov 01, 2012 | Necchi Sewing Machines

1 Answer

I have been looking for a foot-control for my model 524FB to no avail. Any suggestions?

Check out I saw a foot control for a Necchi 524 there for around $25. I hope it was you are looking for. Good luck

Dec 29, 2010 | Necchi Sewing Machines

1 Answer

I have a necchi sewing machine. How and where do you insert the bobbin in model 525fa

if you have a snap in sewing table remove it first
at the bottom in front of the needle plate area is a bobbin case door
when you open it there is the bobbin case & also should be the feed dogs
always keep the bobbin area clean of lint or loose threads
take note of how the bobbin case is inserted in the bobbin area,, see where the thread tail is at on the bobbin case
then make sure the bobbin is wound correctly or it can cause sewing problems
reinsert the bobbin into the bobbin case the same way it's removed

I also have a necchi sewing machine, the base of your is like the base of mine, if you need a picture of inserting the bobbin,, send me a comment with your email address & I will send you a picture of the threading the bobbin case & inserting it

Nov 17, 2010 | Necchi 3101 Mechanical Sewing Machine

1 Answer

Problem inserting bobbin

Inserting bobbin into the bobbin case or problem inserting bobbin case into the shuttle?

Make sure the thread will feed from the bobbin clockwise and through the guide on the bobbin case.

Lift the lever on the bobbin case to hold the bobbin in place as you inset the bobbin case into the shuttle.

If the bobbin case for this machine as a "finger", this has to align with the opening in the shuttle.

If you cannot readily see this - move the bobbin case a bit to the left and right until it clicks into place.

Feb 20, 2010 | Necchi 6018 Mechanical Sewing Machine

1 Answer

Bobin casing

Look in the bobbin area to see where the screw fell out. Check your manual. Sometimes they have a good picture of the bobbin area.

May 05, 2008 | Necchi 3537 Mechanical Sewing Machine

Not finding what you are looking for?
Necchi 3537 Mechanical Sewing Machine Logo

Related Topics:

434 people viewed this question

Ask a Question

Usually answered in minutes!

Top Necchi Sewing Machines Experts

Douglas Plant
Douglas Plant

Level 2 Expert

176 Answers

Irene Tulloch

Level 2 Expert

458 Answers

Derek Massey

Level 2 Expert

92 Answers

Are you a Necchi Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides