Fan runs but there is no cooling. - Heating & Cooling

Both radiator cooling fans are running all the time ? Key off ? The cooling fan opperation
HOW they work
Cooling Fan Control
The engine cooling fan system consists of 2 cooling fans and 3 relays. The relays are powered by the battery positive voltage circuit and controlled by a switched ground from the powertrain control module (PCM).
During low speed operation, the PCM supplies the ground path for the low speed cooling fan relay through the low speed cooling fan relay control circuit. This energizes the cooling fan low relay coil, closes the relay contacts, and supplies battery positive voltage from the COOL FAN LO fuse through the cooling fan motor supply voltage circuit to the cooling fan. During high speed operation the PCM supplies the ground path for the cooling fan low relay through the low speed cooling fan relay control circuit. After a 3-second delay, the PCM supplies a ground path for the cooling fan high relay and the s/p cooling fan relay through the high speed fan relay control circuit.
The PCM commands the fan on under the following conditions:
• Engine coolant temperature exceeds approximately 98°C (208°F) Low Fan Speed
• Engine coolant temperature exceeds approximately 102°C (216°F) High Fan Speed
• A/C refrigerant pressure exceeds 361 kPa (52 psi) Low Fan Speed
• A/C refrigerant pressure exceeds 2100 kPa (300 psi) High Fan Speed
• When the engine coolant temperature exceeds 112°C (234°F) at key off, the fan high speed will run for up to 300 seconds. If within that time frame 102°C (216°F) is reached then fan speed will change from high to low speed. If within that time frame 99°C (210°F) is reached then fan speed will change from low to off.
The PCM commands the fan off under the following conditions:
• A/C is requested and engine speed exceeds 6,240 RPM
• Engine coolant temperature exceeds approximately 99°C (210°F) turns the cooling fans from low to off.

sounds like one of the relays are stuck closed .

Cooling Fan Always On
Step
Action
Yes
No
Schematic Reference: Engine Cooling Schematics , HVAC Schematics in HVAC Systems - Manual
Connector End View Reference: Cooling System Connector End Views
DEFINITION: One or both engine cooling fan motors run continuously in high or low speed.
1
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, command the Fans Low Speed ON and OFF.
Are one or both cooling fans ON?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
3
Are both cooling fans running continuously?
Go to Step 4
Go to Step 6
4
Are both cooling fans running continuously in high speed?
Go to Step 5
Go to Step 7
5
Test the low reference circuit of the A/C refrigerant pressure sensor for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 18
Go to Step 14
6
Important: The S/P relay is located under the front bumper on the drivers side of the vehicle.
Remove the cool fan S/P relay.
Did the right cooling fan turn OFF?
Go to Step 10
Go to Step 8
7
Remove the cool fan LOW relay.
Did the cooling fans turn OFF?

you can check the cooling fan by disconnecting the plug at the motor and run jumper wires from the battery directly to the fan motor it should run if its working if it doesn`t run then the cooling fan motor needs replacing. if it does run then check the plug for a bad connection. other things can cause this like the cooling fan relay, the coolant sensor that sends a signal for the computer to turn on the cooling fan by sending a signal to the relay.

condenser fan must run if it is to cool. does compressor run but not fan. fan need to be replaced ... will not cool until it is fixed.

cooling fan not running.check for faulty cooling fan relay or fuse.cooling fan fan should be running when you turn on AC.hotwire cooling fan make sure cooling fan motor okay.

most time coolant temperature sensor faulty.but check cooling fan fuse and relay.then hot wire the cooling fan if fan runs.problem in the fan wiring or pcm.if every thing else okay.if cooling fan dont run when hot wired the cooling fan need replacing fan motor has internal open winding circuit.

HOT WIRE COOLING FAN USING JUMPER WIRES TO BATTERY.IF FAN DONT RUN WHEN HOT WIRED FAN MOTOR BAD NEED REPLACING. IF FAN RUN WHEN HOT WIRED. CHECK COOLING FAN FUSE AND RELAY.IF ALL IS GOOD.YOUR ENGINE COOLANT TEMPERATURE SENSOR NOT WORKING.IT CONTROL COOLING FAN AT SET TEMPERATURE IF SENSOR OPEN OR FAULTY THE COOLING FAN WONT TURN ON.CHECK COOLING FAN WIRES FOR DAMAGE.IF ALL STILL CHECK OUT GOOD HAVE VECHICLE SCANNED FOR PCM FAULT.IF IT FAILS NO COOLING FAN WONT TURN ON.

CHECK COOLING FAN FUSE AND RELAY.IF BOTH GOOD SCAN CAR TO CHECK COOLANT TEMPERATURE SENSOR FAULT CODE.THE PCM AND COOLANT TEMP. SENSOR IS WHAT CAUSE FAN TO RUN AT CERTAIN TEMPERATURE.IF ALL IS GOOD.HOT WIRE COOLING FAN USING JUMPER WIRES TO BATTERY.IF FAN DONT RUN REPLACE FAN MOTOR.IF FAN RUNS YOU HAVE SHORT OR BROKE WIRE IN THE COOLING FAN ELECTRICAL CONNECTOR.

check fuse and relay.if all is good.hot wire cooling fan using jumper wires to battery.if fan dont run replace the fan.if fan does run you have a open wire or bad connection at cooling fan electrical connector.