Question about Epson Stylus CX6400 All-In-One InkJet Printer

1 Answer

Have trouble turning on the machine

I have to push the "on" button several times before it comes on, it prints okay once the machine is on but the "on" button does not work properly.

sometimes the machine comes on with the first press, most other times it takes 5 or 6 times to press the on button.

Posted by on

  • jbm2313 Jan 19, 2009

    I have the very same problem turning the printer on!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 68 Answers

MOST all-in-one printers have a time delay on the on/off button.
Try pressing and holding for a second or two and it should start first time everytime.

Hope this helped.

Nigel
The INK Store
http://www.the-inkstore.co.uk

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

C 1038


Open the front door, up left small access cover remove and push trouble reset button. Once reset the malfunction and turn OFF and ON the Power Switch. If the same malfunction is still detected, check cables for proper connection and, if they are okay, change PWB-B. If you can find one, quite old machine, a legacy Minolta, now Konica MInolta

Mar 04, 2013 | Genuine Konica Minolta Konica Minolta Di...

1 Answer

I have a Canon Pixma MP 130/110 Printer. Machine is not printing. Have been through all the recommended cleaning/ maintenance procedures several times and fitted new ink cartridges all to no avail. Message...


Pixma IP3000
1. Turn off printer.
2. retaining button Resume/Cancel press button POWER - indicator it will catch fire by green color.
3. let go button Resume/Cancel, continuing to retain POWER.
4. press button Resume/Cancel of 2 times, retaining POWER, after which let go all buttons.
5. when indicator will be lit BY GREEN - press button Resume/Cancel of 4 times!!!
6. turn off printer by button POWER.

Mar 06, 2011 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

I am having trouble printing black, sometimes. I can print some things fine, and other pages come out blank. I have cleaned the machine several times (8-10). I changed the cartridge


the cartridge is generic or original, some times generic cartridges make troubles like yours, you clean out the inyectors, machine, heads, all and still you have troubles... try it with other cartridge, some times the inyectors of generic cartridges came jammed, so you can clean 100 times and the problem persists, try with another cartridge, witout clean the inyectors and without make any service...

Aug 16, 2010 | Brother MFC 240C All-In-One InkJet Printer

1 Answer

Cancel printing is on and will not turn off after canceling when pushing the stop/exit button. i cannot print anything else. when i turn it off and unplug it then plug it back in for 1 min and turn it back...


You did not list your model but if it is an MFC series then try turning off the machine and then hold down the clear/stop button while turning the power back on. Continue holding the button for a few seconds. This procedure will clear whatever may be stuck in memory. This works on most Brother models but may not work on yours.
Good Luck and Thank You for using Fixya.

Aug 12, 2010 | Brother Printers & Copiers

6 Answers

Clean unable 46, See Trouble shooting and routine maintenance chapter in User's Guide.


Hi there. . . okay . . . Follow this step
1.) Unplug your printer.
2.) Plug your printer again while holding the menu button 15 sec.
3.) select 8 by using the arrow buttons ,push OK and select 0 and push OK
4.) then numbers appear looks like this ###:### ###:###.
5.) now push the MONO button until the purge:#### appears on the LCD
6.) Select 2, push ok, select 7,push ok,select 8,push ok, select 3,push ok

7.) - switch off the printer ,switch it on
- ready to print
- CHEERS!
 email me if I help you. . ryuuzaki182@gmail.com 

Mar 20, 2010 | Brother DCP 165C Compact Color Inkjet...

1 Answer

Waste ink reservois is full


Hi
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Feb 02, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Paper comes out blank


Ok here is the code you need.
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 08, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Screen says ,Unable to clean see trouble shooting and routine maintenance chapter in users hand book, when i refere to hand book it says remove any foreign objects ie ripped paper/paper clips or disconnect...


hi every1 step by step
- pull out the AC plug
- put back the AC plug while holding down the “menu” button and keep holding it (15 sec)
- now you are entering the MAINTENANCE mode and “error 46” pops up in the display
- select 8 by using the arrow buttons ,push OK and select 0 and push OK
- 00:00 00:01 OK (the display is showing this message)
- now push the MONO button 25 times until you see PURGE: xxxxx
- Select 2, push ok, select 7,push ok,select 8,push ok, select 3,push ok
- the purge counter indicates now: purge: 00000
- switch off the printer ,switch it on
- ready to print
- CHEERS!

Mar 05, 2009 | Brother DCP-120C All-In-One InkJet Printer

1 Answer

Keep getting 10.00.03 supplies error, have tried turning the machine off and on several times.


10.00.03 - The printer cannot read or write to the yellow print cartridge memory tag.

Solution:


Turn the printer off and then back on again.

If error returns, remove all print cartridges and turn off the printer.

Cold reset the printer:

Turn on the printer.

Watch the control panel.

When the memory starts counting, press and hold the green (Select) button.

Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.

Release the check button when the Ready, Data, and Attention light are on steady.

The control panel will display SELECT LANGUAGE.

Press (Down Arrow) button once. The control panel will display COLD RESET.

Press (Select). The printer will perform a cold reset and then continue its power-on sequence.

Wait for the printer prompt to install each print cartridge.
This should return the machine to operating condition. If you still get the error, replace the yellow print cartridge.

Jan 15, 2009 | HP LaserJet 4600dn Color Printer

Not finding what you are looking for?
Epson Stylus CX6400 All-In-One InkJet Printer Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...