Question about Onkyo TX-DS484 Receiver

2 Answers

Onkyo TX-DS484 Receiver

Two problems with the TX-DS484 receiver (about 5 years old) 1. I have output to the speakers only in Stereo mode - if any other mode is selected there is no output. I have front, center, and rear speakers connected. For a while this problem was intermittant but now the only way I get output is in Stereo. 2. More recently the output level from the Video 1 input (from the cable box) is very low. Volume needs to be at about 75 where the volume from FM is about 40. I move the audio to Phono and the stero audio level is fine. Any thoughts - or is this unit junk??? Thanks.

Posted by on

  • 2 more comments 
  • bilboom Dec 15, 2007

    hi, i have exactly the same problem and no solution, may be buy another receiver

  • bilboom Dec 15, 2007

    same problem, but no solution help us lol

  • Anonymous Jan 24, 2008

    We had this TX-DS484 receiver for years and it's works very well. Today while I'm watching a movie on DVD, I accidently touched a button in the remote control. The sound muted. I tried every key to bring the sound back but did not work. I don't know which key I had touched and what is wrong.

  • Phil Haus Mar 06, 2012

    I know it has been 5 years. However, did anyone eventually figure out the problem... or better: How to solve it?!

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Unit will not maintain the balance after the unit is powered off

Posted on Sep 29, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you set all your parameters (see manual, page 15)? After that, you can then also change the levels of each speaker (page 16) also.

Posted on Dec 17, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ONKYO TX-DS484: \r\nI am not getting any sound out of my left speaker on stereo. I cannot find a balance adjustment. I do not have the remote control. Thanks


It sounds like you also need the manual.

http://www.retrevo.com/support/Onkyo-TX-DS484-Receivers-manual/id/365dj182/t/2/


The remote is an RC-4278. You WILL need it.

$25.10 on eBay expiring tonight so jump on it. 3h 35m 40s (Sep 06, 201120:16:46 PDT)

http://www.ebay.com/itm/ONKYO-RECEIVER-REMOTE-CONTROL-RC-385S-RC-373M-RC-371M-/290597112430?pt=LH_DefaultDomain_0&hash=item43a8f00a6e

As far as the left speaker goes, swap it to decide if it's the speaker, wire or the amp channel. There are no control settings that would make one of the front pair go silent.

Sep 06, 2011 | Onkyo TX-DS484 Receiver

1 Answer

Connect mp3 on onkyo tx-ds484 ?


buy an attachment at Radio Shack - Ipod cable to 3 rca cables; plug the rca cables into the
CD input; leave the video cable hanging. It is not a charger, so you will need to re-charge your ipod.

Dec 27, 2009 | Onkyo TX-DS484 Receiver

1 Answer

I have an Onkyo Av Mod# TX-DS484. The sound is out, all other functions work normally. I did notice that preceeding the failure the sound amplification seemed to be failing (had to turn it up). Is there a...



After receiving information and suggested actions from FixYa it was able to determine that most likely, a power outage and surge had caused the speakers need recalibrating. It was a simple task which utilized the remote, now it works fine.

Jan 02, 2009 | Onkyo TX-DS484 Receiver

1 Answer

I don't know what happend


Check multi channel output make sure it is Speakers A or B and connect accordingly.

Feb 06, 2008 | Onkyo TX-DS484 Receiver

1 Answer

Trouble with the hooking up wiring for receiver, DVD/VCR combo and satellite to new DLP TV.


Jar50, lacking model numbers for your TV and Satellite, I would suggest connecting your DTV Satellite OPTICAL out to your 65"DLP. Connect your 65"DLP OPTICAL out to your Onkyo TX-DS484 OPTICAL in. If you are using the DIGITAL COAX, just substitute the instructions above from OPTICAL to COAX.
Hope this helps.

Aug 28, 2017 | Onkyo TX-SR803 Receiver

1 Answer

Onkyo receiver playing in mono only


sounds like a reception problem. Is there a visual meter for the reception? Check your antenna.

Feb 02, 2007 | Onkyo TX-8210 Receiver

Not finding what you are looking for?
Onkyo TX-DS484 Receiver Logo

Related Topics:

888 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

 Grubhead
Grubhead

Level 3 Expert

5349 Answers

The Knight
The Knight

Level 3 Expert

75178 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...