Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Blinking green timer lamp of death

Unplugging and resetting used too fix this problem for me that stopped working about 2 weeks ago if u have any insite into this problem I would be greatly thankful I'm pretty handy but never done this type of work i'm guessing its the caps at fault but not sure. If u have any tech info on this don't have $1000 bux to fix this but cant see putting it out to the crub for someone else to fix

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Pull the back off and look at the power supply board....the one with the big black heat sinks. The capacitors will be swollen on top. VERY easy to see what ones are bad. I think they are 4700uf at 25volts. The board is on the left side when viewed from the back. These sets are VERY difficult to work on, but the power supply isn't too bad to get to. Stay to the left of the t.v. and you'll see a few screws that hold the unit inplace. It will slide out once removed. Take you time and just look...You'll see how it's held in. Very do-able fix. These sets have alot of problems down the road, but the power supply is a easy fix that may buy you some time.

Posted on Dec 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yesterday, our 61 inch panasonic projection tv showed pink colors on the lighter colors in the picture. This morning it has two large black stripes across the picture. What could this be? We changed the...


You may have not reset the lamp counter after replacing the physical lamp. To do this 1. Press the “POWER” button so that the projector projects the picture on the wall (projection screen)
2. Press the “MENU” button to show the “MAIN MENU”
Use buttons “F” or “G” and select “OPTION”
3. Confirm this by pressing “ENTER” so that “OPTION” is shown
Using buttons “5 / 6”, select “LAMP RUNTIME” (lamp operation counter)
4. Select and press the “ENTER” button for at least 3 seconds
5. The “LAMP RUNTIME” (lamp operation counter) will change to “TIME RESET[POWER OFF]”
6. Turn the device off by pressing “POWER” and unplug the power cord

Sep 09, 2010 | Panasonic Projection Televisions

3 Answers

I have a Mitsubishi WD 52628. I replaced the tv


try turning it on hold the menu button for eight seconds menu pops up try reseting the settings again as before you had the problem

Jan 23, 2010 | Mitsubishi WD-52628 52" Projection HDTV

1 Answer

Problem w/ Mitsubishi WS-65869After losing power


I found this answer and I believe it fits your problem perfectly.
Your TV has two microprocessors that depend on each other for communication. The problem is that a power glitch gets them out of sync. Try this:
1. Press the power button and wait for the blinking light to stop.
.
2. Press all the front panel buttons one at a time, except for the reset, and power button.
This will send a command to one processor and sets an interrupt.

3. Hit the power button, and the TV should power up.

4. Set the TV to low energy mode(see TV manual to find out how to do this. Doing this step will help prevent the problem from coming back. These instructions were taken from a Mitsubishi service manual.

Oct 03, 2009 | Mitsubishi WS-65869 65" Rear Projection...

1 Answer

I HAVING PROBLEMS WITH MY CABLE TV. MY DVR WILL NOT COME UP AND ALL MY CHANNLES IS SHOWING NOT AVAILABLE AND MY ON DEMAND DISPLAYS AN ERROR MESSAGE AND I PAY MY BILL 2 WEEKS AGO AND NOTICE THAT THE POWER...


Good Day, albertgaw;
Since TV is showing an image I would suspect the cable/sat box. Try rebooting box again, unplug or hold power button in for 5-8 seconds, be patient and allow several minutes to allow box to reset. If no fix call your provider to resend the signal, or arrange to have box replaced.
Good Luck, big IRISH.

Jul 15, 2008 | Projection Televisions

1 Answer

APPROXIMATELY 3" GRAY LINE ACROSS THE TOP OF MY TV


Do you happen to have a cable box? (reset cable box also by unpluging it). is that line also showing on dvd player on different input?

Jul 01, 2008 | Toshiba 50HM67 50" HDTV

1 Answer

"MY TOSHIBA MODEL:50H60 has the same problem it had 2 years ago..."


Well Since you said the magic Word "PACKERS" ill do my best!
Check fuses F850,F851,F852 look for bad solder joints on jumpers around convergence amps.

Dec 05, 2007 | Toshiba 50H72 50" Rear Projection...

1 Answer

Samsung DLP TV won't come on


It is called a DMD bord and you can fix it your self look at my ether post on how to clean and tighten the screws on it this should fix it

Nov 18, 2007 | Samsung HLN5065W 50" Rear Projection...

2 Answers

HDTV


You can manually reset, by unplugging for about 1 hr. this may help not sure what set so don't have much insite.

Sep 21, 2007 | RCA R52WH76 Television

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...