Question about Quintum Tenor DX2048 (501012100) 2x10/100 Mbps Networking Switch

1 Answer

I need quintum CLI configuration manual - Quintum Tenor DX2048 (501012100) 2x10/100 Mbps Networking Switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Pls cq

http://www.quintum.com/support/mgmt/index.shtml

u find GUI configuration software & also CLI Configuration manual

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Motorola rfs6000 default password


Motorola RFS Default Password

Default Ip address ==> 10.1.1.100

Username ==> admin

Password ==> superuser

for CLI==> RFS6000login ==> CLI

Mar 27, 2012 | Motorola RFS6000 Wireless Switch - P/N...

1 Answer

NEED QUINTUM PASSWORD RESETTING


The detailed description of Configuring Terminal Software/Assigning IP address to Tenor DX is given below.If you need only RESETTING GOTO STEP 18.

1.From your PC, click on Start> Programs> Accessories> Communications> HyperTerminal. The Connection Description is displayed.

2.Enter a connection name (i.e., name for each unit such as Tenor DX 1 and click Ok.

3.Choose the connection port on your PC from the Connect Using drop down list box (i.e., Direct to Com1). Click Ok. The Com1 Properties window will be displayed. See Figure 3.

tinualbinale_22.jpg
4.From the Bits Per Second drop down list box, choose 38400.

5.From the Data Bits drop down list box, choose 8.

6.From the Parity drop down list box, choose None.

7.From the Stop bits drop down list box, choose 1.

8.From the Flow control drop down list box, choose None. Click Ok. A connection to the Tenor unit is established.

9.Click on Call>Call. A connection to the unit will be established. The login prompt appears.

10.Enter a login name. The default login name is admin.

11.Enter a password. The default password is admin. (Once you are up and running, changing the password is a good idea for security purposes). Step through each of the following parameters and enter the correct values for your installation: IP address, Subnet Mask and Default Gateway.

12.At the Quintum prompt, type ei to reach the Ethernet prompt and then type config to change to the configuration mode.

13.To set the IP address, type set ipa followed by the IP address.

14.To set the Subnet Mask, type set subnetmask, followed by the subnet mask.

15.Type siprd to change to the Static IP Route Directory.

16.To set the Default Gateway IP, type change 1 g followed by the IP address for the default gateway IP.

17.Type submit.

18.Type maint to reach the maintenance mode and then mc. Type reset. A confirmation message will ask if you want to reset the unit. Type yes to reset the unit. The reboot enables the Tenor to incorporate the new settings.

19.Once the IP information is set, you are ready to configure the unit.

Jun 04, 2011 | Quintum Tenor DX2060 (501-0122-00)...

1 Answer

I nees to setup Quintum A800 for termination can anyone help me


Command line for termination A800 (Quantum)



Config unit 1# online 1

Config sys# mindn 10

Config sys# maxdn 20

Config pstntg 1# pass 0

Config pstntg 1# cassig 6

Config pstntg 1# super 3

Config pstntg 1# lamp 1 country code (91)

Config pstntg 1# Answerdel 120

Config pstntg 1# lamp 1 9101 01

Config pstntg 1# dis 1 a (ALL - ports)

Config pstntg 1# ena 1 a (ALL – ports)

Config gkadmin allow 1# ip xxx.xxx.xxx.xxx (GW ip + switch-ip)

Config dsp# voice 81 (for g723) voice 68 for (G729)

Config# submit




Local information

Name of this zone Hello
Country selection Canada
Local country code country code (91)
International prefix country code (91)

Hop-off PBX Numbers

91 public

9101 01 public

This configuration for termenation

Nov 20, 2008 | Quintum Tenor A800 (501-0026-00)

1 Answer

At-8624t


How to Configure the Switch
Some configuration is necessary to enable the switch’s advanced switching
capabilities. This is achieved via the Command Line Interface (CLI). On the
AT-8624T/2M, you can also use the Graphical User Interface (GUI).
Using the CLI to configure a switch
1. Connect a terminal or PC to the Terminal Port (ASYN0).
Using the supplied RS-232 DB9 serial straight-through cable, connect your
terminal or PC to the RS-232 Terminal Port:
• For the AT-8624T/2M and AT-8624PoE, the RS-232 Terminal Port is on
the front panel.
• For the AT-8648T/2SP, the RS-232 Terminal Port is on the back panel.
2. Set the communication parameters.
Set the communication parameters on your terminal or terminal emulation
program to:
• Bit rate: 9600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
3. Log in.
After the switch has booted, the login prompt appears. If the login prompt
does not appear, press [Enter] two or three times.
When the switch boots for the first time it automatically creates an
account with manager privileges. The account has the login name manager
and the password is friend.
At the login prompt, enter the login name and password:
Login: manager
Password: friend
The switch’s command prompt appears. Now use the CLI to configure the
switch.
Using the GUI to configure the AT-8624T/2M switch
This section describes how to establish a connection to the AT-8624T/2M switch
through the GUI so you can configure it before installing it in your LAN.
1. Select a PC to use and identify its subnet.
You can browse to the switch from any PC that is running a supported
operating system with a supported browser installed. JavaScript must be
enabled. If you are using a toolbar or plug-in on your browser to block popups,
disable it while using the GUI. The GUI displays detailed configuration
options and information in pop-up windows.
2. Connect the PC to the switch.
Use an Ethernet cable to connect an Ethernet card on the PC to any one of
the switch ports.
You can browse to the router through any VLAN, as long as you give that
VLAN an IP address. These instructions assume you are using vlan1. All
switch ports belong to vlan1 by default.
3. Access the switch’s command line interface.
Access the CLI from the PC, as described in the previous section, “Using
the CLI to configure a switch”.
Installation & Safety Guide 13
4. Enable IP.
enable ip
5. Assign the vlan1 interface an IP address in the same subnet as the
PC.
add ip interface=vlan1 ip=ipaddress mask=mask
6. Save the configuration and set the switch to use it on bootup.
create config=your-name.cfg
set config=your-name.cfg
7. On the PC’s web browser, bypass the HTTP proxy server, if
necessary.
8. Point your web browser at IP address for vlan1.
9. At the login prompt, enter the user name and password.
User Name: manager <the default>
Password: friend
The System Status page is displayed. Select options from the sidebar menu
to configure and manage the switch.
For context-sensitive online help, click the Help button at the top of the
sidebar menu or on any pop-up page


I hope this helps you out
podum

Sep 01, 2008 | Networking Hubs & Switches

1 Answer

Who can help solve my problem


The CM stands for "Configuration Manager", in other words, that is the GUI. The Tenor firmware either starts with a P or an S (e.g. P104-11-00 or S105-01-01)

Sep 17, 2007 | Quintum Tenor ASM200 (501-0132-00)...

1 Answer

Save config


After changing all the necessary parameters using the CLI, use the write command to save your system configuration. If you receive any error messages, your configuration has not been saved. You must correct the errors and re-issue the write command. Notification of write errors is presented in a two column display: ? The left column contains the parameter values that you set in this session and need to be changed. ? The right column contains the parameter values currently saved in the Cajun P116. Wait 15 seconds for confirmation of the write process. Then exit Privileged level by typing exit at the prompt. For example, CajunP116-priv# exit. The cursor changes to CajunP116> to indicate that you are in Normal level. Verify that all the parameters were accurately saved by using the show all or show all list command. The Cajun P116 is now ready for cabling and operation. You may exit your CLI session.

Aug 23, 2007 | Lucent Cajun P116T (108360843) Networking...

2 Answers

Quintum DX2060


http://www.quintum.com/support/products/2G/tenor_2G/sysdoc/webhelp/calleridgeneration.htm

Try the search box at this URL: http://www.quintum.com/support/
Just copy & paste the parameter name into the box.

Jan 13, 2007 | Quintum Tenor DX2060 (501-0122-00)...

Not finding what you are looking for?
Quintum Tenor DX2048 (501012100) 2x10/100 Mbps Networking Switch Logo

Related Topics:

3,141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quintum Networking Hubs & Switches Experts

Mike

Level 3 Expert

4331 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Quintum Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...