Question about Heating & Cooling

Open Question

Potterton Suprima boiler red light flashing. reset allow heating to work for short period of time and then red light flashes again

Posted by on

  • Anonymous Dec 12, 2008

    boiler tries to fire up then cuts out.After 3 attempts it locks out and red light comes on

×

3 Suggested Answers

  • 1 Answer

SOURCE: Repressurise Potterton Performa 24 boiler

hope this is helpful. On my potterton 24 combi boiler it is the valve that sits the lowest, with a slight indent in the black tap. if you turn this for a short period you will hear a hiss and the pressure will quickly build to the desired pressure, when you can them turn the tap back off.

Posted on Feb 05, 2009

bunnydawg
  • 5158 Answers

SOURCE: My daughter is in rented

here is the manual you need

http://www.potterton.co.uk/docs/Potterton_Suprima_HE_User_Guide.pdf

please take a moment to rate this solution thanks.

robert

Posted on Sep 27, 2010

walterkunesk
  • 683 Answers

SOURCE: My boiler keeps cutting out

try turning the power off the boiler and turning it back on, let me know.

Posted on Feb 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Potterton Suprima 30 - Hot water is working - no problem. But the heating doesn't. When I switch the heating on at the controller and turn the thermostat up - nothing ! The boiler status light doesn't...


I am going to assume that there is a pump to move the boiler water to the heat registers. If this is the case then look for an on/off switch for the pump motor or maybe the pump has seized up and needs to be replaced.

Oct 02, 2013 | Heating & Cooling

1 Answer

Model G5RA096C-16 motherboard light flashes one time pauses then flashes again and so on. The furnace turns on and blower turns on but does not heat. What does the flashing light mean?


Your furnace is off on a safety limit. Look for small thermal disks around the burner area they will have a usually red switch in the center and 2 wires coming into it. Reset this and watch furnace run. These are called rollout switches and they trip when you have flame rollout. SO WATCH IT RUN. If you have flame rollout you will most likely have a cracked heat exchanger if so you will need a new heat exchanger or new furnace. Next the number of flashes is important on some furnaces it will tell you what part is faulty. Count the flashes then on one of the furnace covers is the wiring diagram it will tell you what the flashes mean otherwise you can tell me and Ill help you out, WHen you reset the power on the furnace does it try to heat tell me what all happens when you shut the switch off then back on. when you turnit back on make sure the stat is calling for heat,

Dec 13, 2010 | Heating & Cooling

1 Answer

Repressurise Potterton Performa 24 boiler


hope this is helpful. On my potterton 24 combi boiler it is the valve that sits the lowest, with a slight indent in the black tap. if you turn this for a short period you will hear a hiss and the pressure will quickly build to the desired pressure, when you can them turn the tap back off.

Jan 07, 2009 | Heating & Cooling

5 Answers

My Drayton Digistat RF3 boiler control is not working. The thermostat module indicates it is sending a signal, but the unit beside the boiler has a red alarm LED lit. I've removed the batteries and turned...


I found that this solved the problem hope it helps you too.

1. Turn off the power supply to the Digistat SCR (receiver unit)
and leave for 5 seconds.
2. Turn on power to SCR unit and check red light is on.
3. Press override button No.2 and check the green light comes
on and boiler fires.
4. Press & hold down button No.1 (Keep depressed), then
press No.2 and keep depressed. {The Red LED light will flash
a couple of times and then it will go out}
5. Now release both the buttons – {the two LED lights should
come back on}
6. Get the Digistat+2RF/+3RF unit and stand two metres away
from the SCR unit with the Digistat+2RF/+3RF unit in your hand.
7. Remove the battery cover and fit the batteries.
8. The Red LED light on the SCR will now flash for approx. 7
seconds.
9. This confirms that the radio signal is being sent and
received.
10. The Digistat+2RF/+3RF and the SCR are now successfully
linked by a dedicated RF address.

Nov 04, 2008 | Heating & Cooling

1 Answer

I have an Alpha CB28 combination boiler and it is not working at all. The bottom neon indicator light is flashing every second and the helpline suggests it is a temperature sensor fault. I have had it...


try tapping the 3 relays on the pcb,"thats the circuit board under the front cover...
it sounds like a dodgy relay thats starts up the pressure fan in next to the flue....
maybe a dry solder joint,maybe a new relay needed....
its a common fault on this model..

Oct 15, 2008 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

684 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2028 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Cris Sparks
Cris Sparks

Level 2 Expert

338 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...