Question about Dremel Variable - Speed Multipro Rotary Tool 395

1 Answer

Need help connecting my rotor to my computer - Dremel Variable - Speed Multipro Rotary Tool 395

Posted by on

  • David Ford
    David Ford May 11, 2010

    Could you be more precise? What rotor and you want to connect it to a computer.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

He obviously means connecting a ROUTER to a computer, as in a wireless router? This will never get answered here!

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Question on Yaesu G-800SA Rotor. Purchased new


sounds like the bushes need replacing when you bought it usually new ones are supplied in the box if not then a good reatiler should be able to get them for you very easy to replace your self if you have some electrical knowledge if not then a shop should be able to do it for a few bucks

hope this helps

John

Sep 14, 2011 | Rotary Tools

1 Answer

Hi there i have a makita HR2470 and last week i was chasing out a wall and it just stopped mid chase,i checked the transformer it was connected too that was fine,then i've checked the lead at both ends all...


Try to make a direct JUMPER.Take an old electrical cord cable and plug it in the electric socket and the other end of the cord with 2 cables already peel off and jump the + and - to the + / - of the hammer and see if power on if so the on/off switch is bad and need to replace.If the problem
persist probably the motor is burn.



If you need more help come back.Post / thumbs / testimonial are welcome!

Dec 03, 2010 | Makita 15/16" Rotary Hammer, SDS, 3-mode,...

1 Answer

Dremel 10.8V cordless model 800 (8000) The speed is stuck on the high setting (variable doesn't work now) and battery lights no longer work. I'm assuming its the switch and now needs expensive repair. Only...


You are right,it will need a slider switch replacement,But first-is it still under warranty?If it is call the costumer support on their 1-800 ...number.If not you could DIY it.Opening the drill is not that hard and as long as you observe the proper orientation and where every wire is connected to,you will be able to disassemble the unit.Inside you could see where the slider switch is connected and how it is positioned.Usually the surface of the switch is burned out and this you have to replace.The next problem is locate the part number it is usually found printed under the slider part.And the next big thing is to order the part and where to order it.Consult the user manual that came with Dremel unit and the ordering address is there.

Nov 06, 2010 | Dremel 8000 01 Cordless Rotary Tool Kit...

2 Answers

The motor runs, but the bit won't turn?


On the dremel 395 there are 4 visible "star" screws holding the unit together. Get a star wrench/screwdriver and remove those. They kind of look like hex bolts, but they are not, so get the star wrenches.

Now wait.

At the neck, where you have been changing collets and tip types, You may or may not have noticed that the first inch of the top of the body of the tool, the green or grey part, can be unscrewed like a light bulb. Unscrew that, usually a good grip will do.

This now lets you see that there are 2 more smaller star bolts that also hhold the body together. remove those and you will be able to easily seperate the two halves of the tool.

Try to keep the motor body, or rather, let the motor body stay in the half that it wants to. The top shaft that ends with the collet neck, will pop out with just a little coaxing.

Between the top shaft and the drive motor, you will notice some remnent of the interconnecting thing-a majig, that is looking a little ugly right now and needs a replacement. This piece connects the outer shaft and the internal motor.

I know this because one of my first calls tomorrow is to order a replacement part for myself. And I think I will order 2. It seems as though this was not a good design development, in this series.

Good luck with your repair. I do not think it is that complicated. Pull it apart, throw out the debri, use a can of compress air for your computer, put in new part, put back in 6 screws, fire it up again.

Tom P

Nov 03, 2009 | Dremel Variable - Speed Multipro Rotary...

2 Answers

Stripped plastic coupler on output shaft of Dremel model 277


I'm guessing, but I think that the Sears tool uses the same flexible coupling. If you go to www.searspartsdirect.com and put in the model 572610031, you can look at the diagram and decide for yourself. I think the part costs $2.57. If it's the right one, I'd order two or three for the future.
Hope this helps.

Oct 04, 2009 | Dremel Variable - Speed Multipro Rotary...

1 Answer

Trouble connecting flexidrve to the rotary tool


I would go to dremel.com for information they also have a tech service number there that can help. I had it but misplaced it. Let me know if you still have trouble and I will find more information

Aug 28, 2009 | Dremel 300 1/40A "Multi Pro" Rotary Tool...

1 Answer

How to change 400 xpr brushes


I went to Dremel.com and found a parts explosion for this tool and the shunt appears to be connected to the brush holder. It is a little fuzzy on the print. If you go to their site they have a toll free number that you can talk with a tech and they will be glad to help. If I have helped you with the problem would you please rate this response accordingly and thank you.

Aug 15, 2009 | Dremel 400 Xpr Rotary Tool

1 Answer

Dremel Model 395 Type 3 Plastic Drive Shaft Connection broke into pieces. Replacement needed.


You can call Dremel direct at 1-800-437-3635 and order the part. Let me know if you need more information.

Apr 14, 2009 | Dremel 395 Variable Speed Multipro Rotary...

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dremel Rotary Tools Experts

Mike

Level 3 Expert

4331 Answers

Brad Brown

Level 3 Expert

13536 Answers

Mike Carew

Level 3 Expert

958 Answers

Are you a Dremel Rotary Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...