Question about Indesit W 123 Front Load Washer

1 Answer

Indesit WIDL 106 wont start -ON/OFF-Door Led Flashes rapidly

I can not start WIDL 106 washing/dryer machine. As soon as I plug the machine, ON/OFF-DOOR, Function Buttons and Drying LEDS Flashes rapidly. Recently I changed the washing machine wash element. Since then I run couple of trouble less washing cycles. Then the problem starts.
I manage to run the programs several times, although the LED were flashing by plug/unplug the pover supply cable. Every time it was harder and longer to run the programs, until it stops responding completly.
I think it is related to the electronic of the machine, but I would like to get your expert opinion.

Posted by on

  • Anonymous Mar 26, 2014

    Cycle runs and stops as normal but lights continue to flash

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

It is a defectiv controller pcb. I think the eeprom on the controller pcb lost its program (happens often on Indesit machines).

The only solution I know is to change the controller pcb, - not a cheap solution.
I have the same problem with WIDL 106.

Posted on Oct 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What fault code on a Hotpoint BWM129 does Door Lock LED rapidly flashing along with Delay Start LED flashing intermittently represent?


replace the motors brushes check the filters
and clear any bits of bra wire etc

then reset the machine {usually hold power in and apply the mains}

May 25, 2014 | Hotpoint Washing Machines

1 Answer

Indesit washer/dryer widl 126s


Hi gmarf....to reset your machine to cancel those symptoms, Unplug your machine from the Wall Outlet for a minimum of 1 minute. Upon restoring power, it should be reset and ready-to-go.....If you have any further questions or issues please update your post....good luck my friend

Aug 12, 2007 | Indesit W 123 Front Load Washer

1 Answer

Program stops led blink


It is a defectiv controller pcb. I think the eeprom on the controller pcb lost its program (happens often on Indesit machines).

The only solution I know is to change the controller pcb, - not a cheap solution.
I have the same problem with WIDL 106.

Nov 01, 2012 | Washing Machines

1 Answer

Hi, I was going to wash a machine this morning - I have an indesit WIDL 106 Washer-dryer. But as I press the start button all the lamps on the control panel start to blink rapidly and they blink...


It is possible that the machine does not start off the cycle because there are errors or back feedback from the inputs. The processor of the program controller has hung up and so the display is indicating with the blinking. This can be a failure of the program controller unit which must be estimatted. For the program to start up the main program controller must initiate the INLET valve to open up and allow water to flow into. If this does not happen then the voltage at the inlet valve must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

please check the link for support, post your request to

http://www.indesit.co.uk/indesit/entryPoint.do


Jul 02, 2011 | Indesit Washing Machines

1 Answer

Indesit Widl 102 Flashing lights, wont turn on


Hi


Thanks for using FixYa. It seems to be the issue with the Thermal Fuse going bad and/or its panel that is going bad. To start with check the Thermal fuse which is mounted to the exhaust duct inside the back cover panel. Please do accept the solution if the issue is resolved or post a comment with a more detailed question including the manufacturers name and model no# for your dryer so that I can further assist you.


Thanks
Rylee

Jun 14, 2010 | Indesit Dryers

1 Answer

Washingmachine error


Looks like some electric breakdown. Major repairs is requied; probably a new machine. It is now a case for the insurance company.

Sincerely Michael

Dec 03, 2009 | Indesit Washing Machines

1 Answer

Hotpoint BWD129 1200 spin - unwanted drying cycles


This is more a workaround than a solution. When you choose the washing programme (say "D") and push the on/off button, two lights will flash, the "door locked" and the "drying" one. Now turn the "drying programme" button until the "drying" light stops flashing (in my case, this is true when I set the drying programme to 40°C). Then start the washing mashine.

Seems like the function of the drying programme button has shifted against the settings written on the button...don't ask me why! Of course, no guarantee but works for me. Please let me know if it does for you.

Oct 13, 2008 | QuietLine WD-9900 Front Load Washer /...

1 Answer

ON/OFF & Time saver Button keeps flashing


For mine, it started flashing the on/off light along with the "drying high heat" and the "reduce crease".
Unplugging the unit for 30 minutes appears to have reset the machine and it is now working.

Aug 18, 2008 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Indesit widl 126 uk


Turn the control knob to a black dot leave the door open and press the on off button in and out quickly and look for a change in the lilght,, it should blink 3 times rapidly once it does ,, then the machine is reset and ready to use,,,

if you have any problems let me know im here for another hour..

Jan 25, 2008 | Indesit WA 115 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

3,152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

neilmoto

Level 2 Expert

75 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...