Question about Zanussi 23 in. ZDT6252 Built-in Dishwasher

1 Answer

Water not draining completely

G e 1430 potscubber uncounter 14yrs in service

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I fixed a similar problem by changing the ELECTRIC ANTI-OVERFLOW VALVE located at the back of the machine.

water not draining completely - 4ecdc81.jpg

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My GE potscubber water jet is not moveing water . The water is discharging is there help?


most likely ther is a spring returned check ball in the white disk just above the bottom that are known for sticking, but if you open the disk to clean it, you will have to put silicone on the outer edge of the disk and wait a full day before use. if the disk is not sealed well, the washer will not drain all the way.

Aug 26, 2015 | GE Dishwashers

2 Answers

My dishwasher will not drain completely


Most likely, the drain pump is clogged or the filter for the main pump is clogged with goo. If, during the drain cycle, water is just "peeing" into the drain line or sink drain, something is clogged. Broken glass, food, bones, etc., can find a way into the main pump mech or into the drain pump. You didn't specify what model washer you have but check the round removable filter found in a lot of Frigidaire dishwashers. Yours could be square, rectangular, etc. Get the users manual if you need help finding out how to clean the filter! Remember, if water can't move freely through the filter, your washer won't spray strongly either. Also, dishwashers will not drain out every drop of water--they will drain past where you can see the water but there will always be a small puddle of water in the motor. This keeps the seals moist and prevents dry-rotting, cracking and leaking.

Aug 18, 2015 | Frigidaire Dishwashers

1 Answer

Water does not completely drain from bottom of dishwasher when cycle has completed.


May just need to take sump apart and clean or you need new drain pump

Mar 23, 2015 | General Electric Dishwashers

1 Answer

Ge potscrubber 800


GE Potscubber 800

Issue: No water.
What works:
- Dishwasher appears to operate normally, just does not call water.
- Water valve works

Suspected:
- Float / float switch

Needed:
How to test float switch

Jun 01, 2013 | GE 24 in. GSD3400G Built-in Dishwasher

1 Answer

DU2100B: Looking for a repair/service manual for this. My problem is that the dishwasher will fill with water, then immediately drains. It rarely does a complete cycle without doing things out of...


Hello,
I don't believe that a service manual exist i have included a image of the parts breakdown for the pump asm. and while taking look at it i believe the the drain solonoid is hanging up,or the drain flapper in the pump asm is hanging open The solonoid is shown is that image as item #5 it connects to the drain flapper shaft item #13 and the actual flapper is number is item #34 and has a sping thats suppose to close it item #35
one of those is staying open not allowing the water to stay in tub on wash cycle
http://www.searspartsdirect.com/partsdirect/part-model/Magic-chef-Parts/Dishwasher-Parts/Model-DU2100B/1429/0130000/X2905652/00006?blt=06&prst=0&shdMod=DU2100B

Good luck,i hope i have help you to figure out what is wrong with your dishwasher.
Gene

Aug 13, 2011 | Magic Chef Dishwashers

2 Answers

Dishwasher turns on but no water is going into the dishwasher it is a GE potscubber 970


Hi,

As there is no water entering the machine, check ;-

Water-inlet valve The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.

Float switch The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.


Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Sep 06, 2009 | GE 24 in. GSD6660GSS Built-in Dishwasher

1 Answer

Water left in the bottom of dishwasher after cycle was complete


If the water doesn't drain from your dishwasher, check these:
  1. Drain line/air gap--A clog in this part is the usual reason that a dishwasher doesn't drain. Remove the drain line to clear any debris from the hose or hose connection at the household drain line connection. Reattach the hose before starting the dishwasher again.
  2. Pump--You can reach the pump from inside the dishwasher. Remove the lower rack, spray arm and support. Look for an impeller, a device that spins around and forces water through the spray arm. This is the wash impeller and beneath it is the drain impeller that pushes the water into the drain port. Replace it if found defective or worn out.
  3. Drain valve/solenoid---The drain valve may have a solenoid with lever that sticks or frozen and prevents the dishwasher from draining. Free up the solenoid and lubricate the lever.
  4. Belt---A certain brand of dishwasher uses a belt to drive the pump. Replace it if broken or worn out.
  5. Motor---Check it if turning or working.Turn the rotor manually to see if stuck and free it up. Replace if defective, it is not serviceable.

Aug 27, 2009 | Frigidaire Dishwashers

1 Answer

Water not draining completely from Dishwasher tub


That usually happens because of a faulty water level sensor, check it out.

May 12, 2009 | GE Nautilus 24" Built-in Dishwasher

1 Answer

Bosch NOT completing cycle NOR draining water


This may or may not be the issue: I have friends that bought a new dishwasher - I'm not certain, but I think it was a Bosch. They did have similar draining issues.

With their dishwasher, the installer did not follow directions properly. Yes, he'd "installed a million dishwashers", but was too self-confident to check the directions for something particular to this machine. There was something about the way one of the drain or supply hoses was supposed to loop around that was unique to installing this brand, and that ended up being the problem.

Make sure that your machine was installed properly in this regard, even if your installer says they know what they were doing. Call Bosch's customer service dept. if you have further questions.

Sep 11, 2007 | Bosch 23 in. SHU5302UC Built-in Dishwasher

3 Answers

Dishwasher Does Not Cycle


IA, these GE pumps have a habit of sticking if the unit hasn't been run for a while. First you want to verify that the motor is in fact getting power, this will eliminate the timer. You can use a meter on the quik connect from the motor while in the wash cycle. If the motor is getting power, see if the pump is stuck by turning the motor vanes (Do this with the power off). If it's hard to turn and then frees up than this was more than likley your problem. You remove the bottom toe panel and will be able to check this out without removing the dishwasher. Catriver..post back

Dec 29, 2006 | GE 24 in. GSD2230Z Built-in Dishwasher

Not finding what you are looking for?
Zanussi 23 in. ZDT6252 Built-in Dishwasher Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Owen Barnes

Level 3 Expert

835 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...