Question about Frigidaire FRS26R4A Side by Side Refrigerator

1 Answer

Hoshizaki model#km 500mah ice to thin going into defrost to soon.How can i adjust the ice thickness?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

If you are getting 5 min freeze cycles the first place to look is the Check valve this is the white triangular housing right above your pump motor it has three stainless screws take this out there is a spring and a seat clean the seat off and then stretch the spring lightly not too much replace and see if this solves the problem.

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do resettingice machine


First find the correct Model number of the machine which will be KM-xxxxx
Go to this page http://www.hoshizakiamerica.com/techsupport/tech.asp
and enter the model number in the 'Get Manuals' box and download and read your specific User Guide. which should contain all you need.

Sep 18, 2014 | Hoshizaki Ice Maker 393lbs 22in Crescent...

1 Answer

3 beep alarm, machine is clean, has new float ***. but still locks out after dumping ice


Did you clean the float switch water tube going into the water trough when the switch was replaced?
Does it make 1 drop of ice,then shut off immediately?
What is the age of the machine?

3 beeps every 3 sec. = Freeze Back Up Timer. Freeze > Specified Setting
Yellow LED marked "F Timer" energizes. Check for F/S stuck
closed (up), WV leaking by, HGV leaking by, PM not pumping, TXV
not feeding properly, low charge, or inefficient comp. Dip switches 9
& 10 allow for factory adjustment of this back up timer feature.

Aug 10, 2011 | Hoshizaki KM-1300S Stackable Crescent...

1 Answer

I STARTED A HOSHIZAKI TOOK TAPE OFF CURTAIN LOWERED BIN CONTROL INTO BIN CONNECTED BIN CONTROL HARDNESS UNIT WORKED GOOD BUT NOW WATER IS LEAKING INTO BIN MELTING ICE IN BIN ANY IDEA OF WHAT COULD BE...


Start by looking for water valve leaking. Turn machine off and if water is entering machine, water valve is not seating. Let me know if you need more than this.

Feb 14, 2011 | Hoshizaki KM-1300S 3-Phase Stackable...

1 Answer

Just replace the bin switch on a hoshizaki 630mab still does nada likes it dead in the water has power going to it.


according to my wiring diagram, the power goes thru the bin switch and then goes to terminal #10 on the control board, #7 on the control board, and branches off and goes thru the control switch and high pressure switch and then to the transformer.
I would check the "Ice/Wash" switch to be sure it is allowing power thru it. See if you have power at the high pressure switch. If you do, control switch is probably good so that would send me to the transformer. See if primary and secondary power is present.
Let me know if I can be of further help

Oct 05, 2010 | Hoshizaki KM-630M Crescent Cuber Ice Maker

1 Answer

If my ice cubes are incomplete from my manitowoc ice machine and I sometimes here them falling early and hitting the bin before it dumps. Is the ice thickness set too thin or too thick? Thanks for your...


Hi,
The ice thickness is too thin...
turn the screw on the ice sensor IN or clockwise about 1/8 turn at a time till you get the right thickness...give it a couple of dumps before making another adjustment after doing the first one...be careful as the sensor is very sensitive and can be knocked out of wack very easily...

heatman101

Sep 28, 2010 | Refrigerators

1 Answer

Km-630mae/where does the L-shaped metal bracket fit inside the float switch. It fell out


small bracket does not go inside, but outside the float switch. It goes behind where the float switch mounts. A screw goes thru the float, the bracket, and then into the machine. It holds the float level to it's adjustment.

Sep 02, 2010 | Hoshizaki KM-630M Crescent Cuber Ice Maker

1 Answer

Machine beeps when turned on ice position cleaning cycle works but no ice is beeing made


first try resetting the board by pushing the reset button on the board. But make note of the number of the beeps before resetting.

Dec 21, 2009 | Hoshizaki KM-630M Crescent Cuber Ice Maker

2 Answers

Why is my Hoshizaki ice machine evaporator frozen


if the defrost/hot cycle doesn't work, the ice won't fall and eventually freeze everything.

Dec 03, 2009 | Hoshizaki KM-630M Crescent Cuber Ice Maker

Not finding what you are looking for?
Frigidaire FRS26R4A Side by Side Refrigerator Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Frigidaire Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...