Question about Philips Magnavox 9P6034C 60" Rear Projection Television

1 Answer

Blank screen no sound

When the power button is pushed the green led comes on but, there is a blank screen and no sound. help!!!!!!!!!!!!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Philips Master
  • 3,459 Answers
Re: blank screen no sound

Common problem. You can get a repair kit from

Posted on Jul 20, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Mitsubishi WD-62526 turns on-n-off

I would bet the illumination lamp has reached the end of it's life (~$40 online). Should be easy to replace. Also possible the ventilation vents need cleaning, which could cause the lamp to overheat and turn off.

Dec 12, 2013 | Mitsubishi WD-62526 Projection TV

1 Answer

I have a 62" rca led hdtv.. when I push the power

How many times does the light flash each time? Also whats the full model number of your set?

May 30, 2011 | RCA Projection Televisions

1 Answer

Hi. I have a problem with my 42 inch plasma tv,when tv is turned on green L.E.D appears on bottom right and tv works as normal.After 40 minutes to an hour tv makes click sound and screen goes blank the...

Hello, A common problem for these is bad capacitors in the power supply, Remove the back from your Tv and look at the power supply on the left hand side.
You will see roughly around 9 x capacitors that are bulged / domed shaped on top usually these are valued at 3300uf 10V any that have bulged or leaked a brown like substance should be changed. This will cure the problem as they overheat being sat next to a heatsink that gets very hot! Try and change them for the same 3300uf but a higher voltage.
I hope that this help to rectify the fault of the projection TV....

May 12, 2011 | Projection Televisions

1 Answer

Sony kdf-37h1000. push power button and the green lite comes on steady and i can hear a fan. never gets to a picture or sound. it then sounds like it shuts power off but lite goes from flashing green to...

Hi catfishbob,
You're lamp came to its peak burning life and now its dead that's why you can't power up the unit and the led light keeps flashing. Once the lamp replace with new one your unit will back to normal again. Click this link for the replacement
Hope I helped you.
Have a nice day!
Thanks for using Fixya.

Mar 05, 2011 | Sony KDF-37H1000 37" HDTV

1 Answer

60SDX88B. No video, No sound. DP06 Protection

not a solution but i have a 50gx30b doing something similar, no picture no sound, 3 green leds are lit up on the main board and then one red led lit up also on main board, front panel red led stays on for about 30 -50 seconds and then it all shuts off, I then have to unplug and replug to get the same results.

Mar 03, 2010 | Hitachi 60SDX88B 60" Rear Projection...

1 Answer

No picture or sound

Remove the rear panel. With the TV on you should see a red LED near the center of the PCB. There should also be 5 green leds, 3 to the left a 2 behind. If there is no red leds, check the fuses. If there are no green leds or maybe 1 or 2, disconect PSD5. It's a connector on the left side of the power board that connects to the audio board. It's the 3rd on fro the back. It's labled. With that disconected, turn on the set and look for the green leds. If all 5 light, the power supply is OK and you have a problem beyond that. If they don't all light you have a bad power supply.

Jul 21, 2008 | Hitachi 50EX20B 50" Rear Projection...

2 Answers

Problems with my 50 inch hitachi ultravision projection screen tv

check the solder around the area of the vertical IC. solder is either cracked or else cold. Cold solder appears as dull. Resolder anything that isnt shiny.

May 20, 2008 | Hitachi 53UDX10B 53" Rear Projection...

2 Answers

Blank screen,power led on, fans running

Do you have a DLP or Plasma set????? Give me the model #.

Apr 01, 2008 | Hitachi 60SDX88B 60" Rear Projection...

1 Answer

Turning On Problem

HLP, HCN HL-S The Start-up Problem or/and
3 LEDs in the front blinking.

Unplug the set, pull out the lamp module (not all the way - leave it on the track) and push it back in.

Power issues (Tv not turning on) were typically due to faulty ballast. While the TV reports a bad lamp it is the ballast itself causing the issue. Samsung is well aware and will replace both the ballast and the lamp (since the lamp can be prematurely aged but the bad ballast). After replacment most people stop having issues.

Feb 06, 2008 | Samsung HLN467W 46" Rear Projection HDTV

1 Answer

Help I have no picture, no sound. red light on front, 3 out of 4 green leds inside.

i would first replace the convergance ic

Oct 22, 2006 | Hitachi 57SWX20B 57" Rear Projection...

Not finding what you are looking for?
Philips Magnavox 9P6034C 60" Rear Projection Television Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66535 Answers

Are you a Philips Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides