Question about Audio Players & Recorders

2 Answers

Kenwood KA-127 P-off response

We have a Kenwood KA-127 that is old and was working but all of a sudden is shut off and when you power it back on it reads P-off. What can we do to get this working? I am not able to find a manual or anything for this? Any ideas?

Posted by on

  • dumbox Jan 22, 2009

    Kenwood KA 127 - "P-OFF" display
    Problem does not appear to be in the Power Outputs. - scope to the input of the protection relay shows good audio - no dc present. Require service information - schematic


×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

This unit is likely to be in "protect" mode. This means that a problem has been detected it the final stage of the amplifier section and the speakers are disabled to prevent damage to either the speakers of the amp. This can be casued by a poor solder connection or defective components inside the amp. Without taking internal measurements, I can not say for sure. Expect a parts cost in the $25-$40 range for this repair. Add in the local labor rate for the total repair cost.

Dan

Posted on Dec 01, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Hello I faced the same problem and finally got it repaired with my trusted technician..together we did it...off course you need the Service Manual..Will have to buy one..

Problem one Detected was (a) K1 relay 24VDC that went defective and we repaired it (b) and then a few resistors and capacitors in the protection circuit supplying the +12VDC and -12VDC and the Amp sprang in to action...contact me for a summary of the same fault..(vu2kfr@gmail.com)
but get hold on the manual..

Buy from - http://www.webstore.com/item,pgr,Kenwood-KA127-Amplifier-Service-Manual,name,49042609,auction_id,auction_details

Posted on Feb 03, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Universal remote codes for Kenwood Ka 87 integrated amplifier


The applicable code would be found in a compatible universal remote.

Jan 11, 2017 | Kenwood Audio Players & Recorders

1 Answer

How do I connect the TV to the receiver. An RCA TV Model #LED58G45RQ TO Receiver KENWOOD Model# KR-A3060 For Audio


If your RCA TV has left and right audio outputs on the rear, connect them to corresponding inputs on the rear of your Kenwood receiver.

Jan 09, 2017 | RCA Audio Players & Recorders

1 Answer

Purchased with paypal through credit card Android charge cables. CC statement shows "DOMINANTMED" with phone 402-935-7733. Not received. No word. Who are they?


probably--- but fortunately you used paypal to do the purchase
ring paypal direct and find out how to get your money back, and tell them what you have done to contact the seller and the lack of response from them
I cannot see how a current would flow through a magnet as the fields of the magnet would affect the current flow
any way it is part of the paypal policy to help you to recover from ripoff merchants

Jan 08, 2017 | Samsung Audio Players & Recorders

1 Answer

What is wrong with my pioneer pdpro6u media receiver?it shut off and wont power up,and there is a blinking blue light what does it mean?


  • there might be speaker wires touching somewhere
  • check all ventilation slats in Receiver make sure dust free
  • Check all connections maybe cable connections mixed up
  • Make sure power cord plugged in all of the way. Also make sure that the cord does not have exposed wires (this could cause a short
  • Make sure the wall outlet you are using is not overloaded (Too much power being used)
  • If this problem persists call customer service
This is the link to the manual
https://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/276752973PDP5060HDOperatingInstructions.pdf

Jan 08, 2017 | Pioneer Audio Players & Recorders

1 Answer

Want to use my current speakers with a new surround sound system. Current system is 5.1 channels, rated at 100w per channel @ 8. Ohms. New System is rated 145watts, 5.2 channels at 6 Ohms. Will b ok?


Hi Ronald.
8 Ohm speakers will work just fine as replacements for the
6 ohm speakers. When fitting speakers you need to consider
The power handling capability. The impedance and the frequencies
involved. Power handling is expressed in wattage ie 100W.
Unfortunately this can be expressed in rms, max or peak music. The rms value (root mean square) is the only really relevant figure as this is the continuose handling power at 1 KHz. The impedance
is the resistance that the amp sees but is not a dc resistance and
varies with frequency. The lower the impedance the more power
will be drawn from the amp. In the event of a short circuit across
the speaker the amp will try to deliver infinite power into an infinitly
small load in an infinitesimal amount of time and will self destruct.
Using an 8 Ohm speaker draws less power than a 6 Ohm speaker.
Connecting speakers in parallel; results in the impedance beingreduced. For example two 8 Ohm speakers in parallel will result
in a 4 Ohm impedance load but in series will be 16 Ohms.
Incidentally the the .1 (5.1) is the sub woofer which only has
to handle the bass frequencies, a small percentage of the
amplifiers overall frequency response..
Connect your speakers and then power up the amp last
after double checking there are no shorts on the speaker
cables.
All the very best from Vintie.





Jan 07, 2017 | Audio Players & Recorders

1 Answer

Can't get my Kenwood VR715 receiver to go into the Select a speaker system to see if speakers are turned on. Followed manual instructions and can't get in. Any Suggestions.


Try resetting the unit by unplugging the unit from the wall, then plugging it in again WHILST holding the power on/standby button in. This should reset the system. If not:
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 06, 2017 | Kenwood Audio Players & Recorders

1 Answer

Kenwood VR-357 Audio Video Surround Receiver manuals


Try Googling (kenwood)(VR-357)(manual) without parens.

Jan 02, 2017 | Kenwood VR-357

1 Answer

How can I find out if my harmon kardon onyx studio Bluetooth speaker isn't burnt out. I've opened it up and nothing smells burnt or fryed. I've bought the account power adapter and will not power on


Do you have an ohm meter?
Any sign of lights at all?
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Mar 15, 2016 | Audio Players & Recorders

1 Answer

I have a monsoon mh505 pc speaker system. i lost the power adapter.i need a manfacture phone number or the model number of power adapter.


We can provide one.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Mar 14, 2016 | Audio Players & Recorders

2 Answers

My headphones connect with the adapter, the blue light is on on both but nothing comes from the ipod. I have performed the factory reset but it still doesn't work. The headphones had worked fine and then...


I have same issue....just took my transmitter apart - the wires connecting the male jack to the silicon board are frayed, disconnected.....you might check that...it's only 2 small screws holding the outercase together....be careful though

Jul 07, 2009 | Logitech Bluetooth Wireless Headphones

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

1,600 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

101516 Answers

 Grubhead
Grubhead

Level 3 Expert

4751 Answers

The Knight
The Knight

Level 3 Expert

71611 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...