Question about DISH Network ViP622 DVR DTV Receiver / 180-Hours Video Recorder

1 Answer

No signal on TV2 with dishvip622.

Tv2 signal was fine for several months. All of the sudden, I started getting no signal on TV2...just a blue screen. I have checked the 2 TV mode...that is not the problem.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

If the blue light on the receiver is on then your tv is most likely on the wrong channel after checking cabeling i would do a reset on receiver first wait for it to come back on, then run a channel scan on your tv2 you can do this with orignal tv remote under the menu options. its also refered to as a auto search or auto program.

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I turned the living room tv on this morning and it is black and white and says no signal. The other tvs are working fine. I have turned it off and turned it back on still nothing


Hi my name is Mike Houston of DISH Network and I see youturned on the living room TV and it was black & white and had no signal.Depending if it's a Dual receiver and if the issue is TV1 or TV2 but there issome thing's you can check to make sure it is on the right channel. I will sendyou two links to help with the setup for both TV1 and TV2, if you have anymorequestions or concerns please e-mail me back at Michael.houston@dishnetwork.com;http://www.dishnetwork.com/SupportSection/bbs-screenand http://www.dishnetwork.com/SupportSection/black-blue-tv2.

Sep 04, 2011 | DISH Network 322 DTV Receiver

1 Answer

Umm my tv2 remote isn't connecting to my reciever so i tried to change the remote address and it doesn't work


Hi my nameis Mike Houston of DISH Network and I see your TV2 remote isn't connecting toyour receiver. You will want to make sure you're at the TV1 location to programthe remote for TV2, press the Menu button 2 times and you will see the SystemInfo screen. On the bottom for the screen you will see the remote address forTV2, make sure the TV2 remote has fresh batteries inside. On the back of thereceiver their will be a Remote Antenna port and you want to make sure that ishand tight. Push and release the SAT button and press record and you should seethe address change for TV2. I will send a link to help with these steps; http://www.dishnetwork.com/SupportSection/remote-control.

Jul 30, 2011 | DISH Network 322 DTV Receiver

1 Answer

I have a new DVR 622 reciever, the UHF remote(TV2) does not work at all, I have tried to program it, but itdoes not seem to work.(does the TV2 need to be hooked up to the receiver to et the remote to...


Hi Rich, myname is Mike Houston of DISH Network and after going over your post I see theTV2 remote as well as other issues with TV2. There is a easy fix to this so youcan enjoy both TV's, on the receiver you will want to make sure it's in DualMode, you will see a Yellow, Blue and Green lights on the front of thereceiver. I will send a link to help with the steps of setting up the remoteand making sure the TV2 is configured correctly and on the right channel. http://www.dishnetwork.com/SupportSection/troubleshoot

Apr 18, 2011 | DISH Network ViP622 DVR DTV Receiver /...

1 Answer

I have a Dish receiver 322. TV1 is set on channel 3 and TV2 is set on channel 116. Everything worked. We moved the receiver and TV1 into another room (right next door to where it was). We triple checked...


Hi hartbettinaI see where your TV2 has a blue screen, there are a couple of things you can doyou can do. The first things you want to do is press the buttons of MENU-6-1-5and see if TV2 is set to channel 60 or 73 and make sure TV2 is on that channel.Once TV2 is on the channel on the Modular Setup page you will want to unplugthe receiver for 10 seconds and plug it back in and it will reset itself. Iwill send a link that will help with these steps. http://www.dishnetwork.com/SupportSection/black-blue-tv2

Feb 27, 2011 | DISH Network 322 DTV Receiver

2 Answers

There is something wrong with the #2 tv function. When we turn on the tv to watch it doesn't work. We have to choose the dvr menu and then select guide to get a tv signal. We also can't use the dvr to...


My tv2 looks very hazy after switch to another TV from the attic but disconnected the one I had. There are 3 coax cables comming from the switch box to the attic...may be connected wrong or missing any connection. I played with all the 3 acbles comming from switch box connection. There is aDP2D splitter and SAT line and VHF/UHF and TV2 to going to TV....Before it worked fine but same TV2 looks hazy now....what did I do wrong....plz help...Thanks.....ADE

Jul 13, 2010 | DISH Network ViP722 DTV Receiver /...

1 Answer

Dish Network 322 will not work both TV's at the same time. If TV1 is on it works fine, but TV2 says aquiring satellite signal. If TV2 is on it works fine, but TV1 will say aquiring satellite signal. Both...


Hello! Dan Busa with Dish Netywork here intermittent signal loss like that is usually caused by some sort of glitch a hard reset ( unplugging it for ten seconds ) will usually resolve this. If your signal strength is at or above 80 that should be fine, but keep in mind you need good signal strength on both the 119 and 110 satellites ideally you should be at 70 .

Jun 25, 2010 | DISH Network 322 DTV Receiver

2 Answers

TV or control doesn't work need help know


ok my tv is doing the same thing and i need help if you found a solution please email me at pieces41096@aol.com

Jul 06, 2009 | DISH Network 322 DTV Receiver

1 Answer

Tv2 light does not come on


hi hammonhph! I will be more than glad to assist you in this concern. Lets program the remote for tv2, lets make sure that the battery's are brand new, please go to the front panel of the receiver, make sure that u have the remote2 with, turn on the the tv1, you got picture, on the front panel of the receiver, you got 1 green and the blue light is off.. push the power button on the front panel of the receiver once to turn off the green light, once its off the tv will show a black, blue or snowy screen, push the up button on the fron panel of the receiver until it shows the system information screen, look for the primary and secondary remote address, primary and secondary remote address should show a number on the white box ex.. 1 and 1 on the green box, secondary is ex 2 on the white box and 2 on the blue box, how to reporgram the remote to the receiver.. press and hold the sat button and wait until all lights lit up, once it all lit up, release it and press any number from (1 to 15) but for this ex is press 9, then press the pound button (#) that is under number 9, once you press the pound button the sat button will flash 3 times and then press the record button once, record button is under the cancel button or view tv button, once you are done check the secondary remote address, it should be 9 on the white box and 2 on the blue box, save the settings by using the remote 1, selct done on the screen and it will go back again to black, blue or snowy screen, press the sat button once on the remote 2 and the big red power button, the blue light should turn on, just in case the blue light dont turn on, press the power button on the front panel of the receiver for 10sec to reset the receiver, it will acquire the sat signal and go to a progress, and it will download the programming guide, check if blue light is not on, press the big red power button on the remote2 to turn on the blue light and it should work. if just incase the blue light dont turn on, the remote is bad and you need to call 1-800-333-3474 for the replacement of the remote..please feel free to get in touch if you have any query..

Jul 06, 2009 | DISH Network 322 DTV Receiver

1 Answer

Problem jumps back and froth from tv1 to tv2


One of the inputs on the back of the 322 box is bad. usaly 1 wire runs from the dish into a seperator that splits the signal into 2 at the back of the box. you will need to call dish and have a new 322 sent out. 1-888-333-3474

Apr 22, 2009 | DISH Network 322 DTV Receiver

1 Answer

Tvs sync together


The receiver seems to be in single mode. On the right side of the receiver press the front panel. A small pop open door will open and inside there will be a MODE button. Press this button and ensure both the green and blue lights are lit on the receiver. If they are now but weren't earlier this should solve the issue however there may be another issue.

Take the TV2 remote to the TV1 location associated with that system. With the TV1 remote and TV on press menu menu on the TV1 remote this will bring you to the System Info Screen. Near the bottom of the screen there will be two remote addresses- primary=TV1 and Secondary=TV2. Using the TV2 remote press and hold the small clear SAT button until all light across the top light up. Now key in a two digit number that is different from the original secondary address at this location and also different than the address for TV1. Now press the pound key and the SAT button will flash thrice. Now press the record button a few times until the secondary address changes to the number you selected. Once this is done you can exit out of all screens on all receivers and go to the TV2 location that was having the issue and it should be resolved. I hope this resolved your issue and thanks for using Fix Ya.

Feb 10, 2009 | DISH Network ViP622 DVR DTV Receiver /...

Not finding what you are looking for?
DISH Network ViP622 DVR  DTV Receiver / 180-Hours Video Recorder Logo

804 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network TV Receivers & DVRs Experts

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Geoff

Level 3 Expert

413 Answers

Are you a DISH Network TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...