Question about LG WFT1071TP Top Load Washer

1 Answer

Step by step pictures showing How to Dismantle Washing Machine for maintenance?

I have very old top load (4.2kg load) LG washing machine. The bottom Left-side front part of the cover is rusty causing it to become imbalance. I think I need to throw the casing and install a rack to support the machine. I never open up a washer before, so I wish there are pictures showing step by step instruction. Any website?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has written 2 tips or uploaded 1 video tip.


    An expert who has answered 20 questions.

  • Contributor
  • 62 Answers
Re: Step by step pictures showing How to Dismantle...

Get the full model and s/n from machine and search on that also try LG...the search may take you there anyway

Posted on Jan 03, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do you remove inner drum on top loading LG Washer WT5170HV?

The whole top of machine must be removed.
unplug electronics and hoses remove upper splash ring remove cap in center of agitator remove bolt holding down remove .
remove inner tub Nut center tube should lift up and out.
next step if your changing shaft is all from bottom.
lot more down there. Take picture b4 and as you remove for ref. to resemble

Jul 03, 2016 | LG Wave WT5170HV 27" Top-Load Washer with...

1 Answer


The first thing I'd check is the water pump if the timer's working ok...

Mar 06, 2014 | Washing Machines

1 Answer

I have a GE HydroHeater front loading washing machine and it is leaking water from the bottom of the door. I havecleaned the gaskets but I dont know what else to do??

To support Jahn's step by step instructions, I found a YouTube video that shows step by step. I hope this helps!

Mar 13, 2010 | GE Washing Machines

1 Answer

Lg tromm wm2277hw rinse spin error OE

An OE error presents if the washing machine has not successfully drained the water in ten minutes. However, the OE error code does not always mean that the washer requires a service call. If periodic maintenance has not been performed on the washer, there are a few simple steps to take before calling for service.
Step 1: Check the drain pump filter.
Items caught in the drain filter will prevent proper drainage. Over time build up can occur from detergents and additives used in the machine. Manually drain unit through the drain hose, then lay a towel down to catch the water, and remove the filter. Clean the filter thoroughly and restart the machine.
Step 2: Check the washers drain hose.
If the drain hose is not installed properly, the washer will not drain properly. The drain hose should not be installed more than 1 meter higher than the bottom of the washing machine.
Step 3: Confirm that the washer is leveled properly.
If the unit is not leveled properly, it will not drain properly. The front of the unit cannot be higher than the back or vice versa. If not properly leveled, the water can flow back into the machine. If this is the cause of the problem, please level the machine using the supplied leveling wrench. When you place a LEVEL on the washing machine, the bubble should be in the center. Confrim that the washer is leveled from side to side and front to back.

Oct 26, 2009 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

1 Answer

The water inlet does not stop during the entire cycle of washing in our NA F70GS Panasonic washing Machine. How to solve this problem?

Its simple..just follow step by step as below:-
  1. Switch off and unconnected both power & water supply.
  2. Lay the unit with the back side facing up.
  3. remove the back & bottom panel
  4. you will see the valve on the bottom tub.
  5. Unscrew the valve cap.
  6. Dismantle the valve by release the connector between steel bracket & hook (white plastic 'T' shape) using small 'playar'
  7. Then you will see a 20 cents coin ( keep into your tabung gajah)
  8. Use the old toothbrush to clean the black rubber valve.
  9. Assemble everything.
  10. Thats all.

Sep 06, 2009 | Washing Machines

2 Answers


Don't know if you've done it, but put a level on the machine itself and make sure it is level. Adjust it front, back and side to side. This may cure your "walking problem".

Jan 28, 2008 | LG WM-2277HW Front Load Washer

1 Answer

Water continues to fill

you replace 'that'by turning off water going to 'it'remove top of machine,take off hose's on valve,fit them to new valve,with the wireing,do it step by,eire

Dec 11, 2007 | GE WDSR2080D Top Load Washer

2 Answers

Washer Leaking

This video will show you how to replace the Bosch washing machine door seal with step by step guide on the process of how to fit and replace

Sep 30, 2007 | Bosch Nexxt Premium WFMC6400UC Front Load...

Not finding what you are looking for?
LG WFT1071TP Top Load Washer Logo

Related Topics:

2,116 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides