Question about Sony LBT-XGR6 CD Shelf System

2 Answers

SONY LBT-XGR6 COMPACT STEREO

Every time I turn on my system it reads " Protect Push Power" and when I do that, it just go's back to that same thimg every time. So if someone out there can help me please email me the way to get it out of that setting.

Posted by on

  • 1 more comment 
  • MABEL CUMMINGS Jan 23, 2007

    Thank you for your help, and can I get it fix at any stero store.

  • Anonymous Apr 20, 2008

    MY PROTECTER CIRCUIT I THINK IS BLOWN

  • Anonymous Mar 14, 2014

    I can't find the operating manual for my Sony LBT D560 Stereo. I would like to record a CD and I don't know how.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks for the obvious answer but what is the solution??

Posted on Oct 31, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 219 Answers

Sounds like your protection circuit has been activated, which usually means that you have some blown output transistors. Good luck.

Posted on Jan 23, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Push Power Protector - Sony MHC-VX777 I am getting Standby message and push power protector .My music system was not operated


Hi!

This is what the manual says:

PROTECT"and "PUSH POWER" appear
alternately.

•A strong signal was input.
Press ?/1 to
turn off the power, leave the system
turned off for a while, then press ?/1
again to turn on the power.

•Check the speaker cables in case
"PROTECT" and "PUSH POWER"
appear alternately again after you turn
the system on.

Jun 05, 2017 | Sony Audio Players & Recorders

2 Answers

HI I HAVE SONY MHC-RV900D WHEN I SWITCH IT ON IT SHOWS PROTECT PUSH POWER. HOW CAN I PLAY MY SYSTEM AGAIN.??


Welcome to FixYa
Do Following...
  • Turn off the System-Turn it off for a while
  • Then turn it back on.
  • Still Problem, Turn Off system and Check the Speaker Code
  • RESET the system .
  • Remove all the connections, leave it for 24hours and then connect it up again
To Reset
  • Unplug Power Code
  • Plug it back again
  • Press Stop , Enter and Power button at Same time
  • Press Power Button to Turn on it
For more Here is the Guide for your Product Click here
Still have Problem The protective device on the amplifier has been activated because of short circuit. (“PROTECT” and “PUSH POWER” flash alternately.) Turn off the unit, eliminate the short-circuit problem and turn on the power again.

Hope you Got a Conclusion..Thanks for Contacting FixYa...

Jun 15, 2010 | Sony MHC-GX40 CD Shelf System

1 Answer

Protect and push power


That is the common symptom of the defected STK-IC in power amp.section that busted already or just a loose connection.First try to resolder the pins of STK-IC if its works! if not that is the time you replace it, so it works normal again. Hope it may helps you...

Jun 08, 2009 | Sony MHC-GX450 CD Shelf System

1 Answer

"Protect" and "Push Power"


i have a sony component push power protect, i have already replace IC but still protect push power

May 02, 2009 | Sony Audio Players & Recorders

1 Answer

Pushed power protect


speaker protection turned on.it can be happend because of bad power amlifire section.can you remoove the powe ramp board with large heatsink.its very easy to repair.and i can help.
nuwan

Jan 09, 2009 | Sony Multi-System Mini Hifi Systems / DVD...

2 Answers

Sony mhc-7av push power protect


Maybe the audio amplifier IC damaged and need to be replaced good luck

Dec 17, 2008 | Sony LBT-LX50 CD Shelf System

5 Answers

PROTECT PUSH POWER IT KEEP SAYING WHAT TO DO


My Sony audio set keeps saying push power protect and the set freezes what should i do? Please help me solve this problem.

Apr 20, 2008 | Sony LBT-XGR6 CD Shelf System

2 Answers

"Protect" and "Push Power"


Doiuble check your wiresa again for no pinches or shorts, even at the back of the unit. Also try unplugging the unit for 12 to 24 hours. If that does not help, it may be the time to buy a new stereo because that means there is a fault in the output device, unless you kinow someone who can trouble shoot and repair solid state electronics.

Sep 18, 2006 | Sony LBT-XGR600 CD Shelf System

Not finding what you are looking for?
Sony LBT-XGR6 CD Shelf System Logo

Related Topics:

422 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5650 Answers

The Knight
The Knight

Level 3 Expert

76016 Answers

Gyula Lacz

Level 3 Expert

486 Answers

Are you a Sony Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...