Question about Sony KV-35S45 35" TV

2 Answers

Pic Bleeding HI Guys, i have this RCA CTC197AH,CHASSIS F27680GY, is running goood exept a bit red bleeding, which i can take out just by reducing the color or adding more contrast,it's not tube because i used in it other chassis and no bleeding.Could it be Red driver,red bufer,or one of the clamps or one of the resistors what you guys think.Thanks in advance

Posted by on

  • Frank Ramiro Jan 22, 2007

    No it has not a tint of red, pic is grait, i turned down the red bias and the bleeding goes away, but it seems that after awhile of beeing on gets kind a vertical 4"band verticaly and pic fads away and i have to unplug it from the wall, and only turns back on after, i let it sit for some time, i suspect this type of set senses this change in the bias and turns off the high voltage,i say this because sound never goes a way i can here channel changing,

  • Frank Ramiro Jan 25, 2007

    Hi i was able to adjust the red bias and no more bleeding, but i have other fault, set runs fine for about 45 minutes and Hoizontal slowly goes out, but keeping sound,i unplug from the wall, and if i let the set sit for some time plug back in it runs again the same cycle,I just learned correct me if i'm wrong,>There is an ERROR code,when i enter the service menu #1,#2,#3,are ERROR CODES.and #1 sais 10,and the other two say 0. also i got the code list and it sais 10, this code means FPIP power supply at reset,what you guys think any suggestions, the set still runs for 45 minutes and shuts the horizontal down keeping sound any help thanks

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Sounds like someone has a weak picture tube

Posted on Jan 06, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 168 Answers

This sympton is characterized by the presence of red, cyan, green, magenta, blue or yellow colour in a supposedly plain white raster. proper colour reproduction cannot be expected if the raster is coloured. this symptom is caused by a poor white balance adjustment of by a trouble in the CRT, colour amplifier, color demodulation or colour output circuits. if the raster has a tint of red or cyan, check the R-Y output circuits and the first grid, second grid and cathode circuits of the red electron gun. but if you dont know anything about this, just bring it to a qualified service technician. good luck!

Posted on Jan 21, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vizio LCD SV420XVT1A-has a red screen when starting then red bleeding through dark


Got to go to settings to change the color of your tv screen and see if that helps

Jan 23, 2015 | Vizio Televison & Video

1 Answer

Brake bleeding cylinder


Sounds like the master cylinder ran empty during the process.
Were you adding fluid as you were bleeding fluid out? If it ever runs empty, you bleed air into the system, and it takes a lot of bleeding to get it back out....You did add fluid as you were bleeding fluid out ...didn't you?

Jan 19, 2014 | 1998 Chevrolet Camaro

1 Answer

Front line blow, replaced line master cly to abs block and from abs to right front wheel. bleed have very low and soft paddle.on 03 gmc 2500 hd 4x4. did not put all the turns and bends back in line does...


Ok here is what you have to do. First off make sure your master cylinder is full, Second your vehicle must be running when you bleed brakes that is equiped with ABS this allows the ABS pump to to run you must bleed both front brakes starting at the passenger side wheel then moving to the drivers side. It will take quit a bit of bleeding and be sure to keep checking fluid level in master cylinder well bleeding. Just remeber the vehicle must be running while bleeding the brakes.

May 12, 2011 | Chevrolet 2500 Cars & Trucks

2 Answers

Why does my front brakes on my 98 zx-9r keep pressure locking ???


I expect it has air in the slave cylinder. Bleeding the brakes will get rid of the air. Check if the brakes are spongy. If they aren't, make sure the spring plates behind the pads are fitted. They ensure the pads are pushed back into the calliper a little bit, reducing heat and wear.

Mar 28, 2011 | 1998 kawasaki ZX-9R Ninja

1 Answer

Still cant get a brake pedal.. been bleeding the lines but not getting much out of them. replaced master cylinder, still no pedal. has all new lines also


you may have to run the motor as you bleed the brakes so the abs hydraulic unit can purge any air that might be caught within the unit itself.did you bench bleed the master cylinder before installing it on the car.this can save time and reduce the possible chance of air entering the system.make sure you don`t allow the master cylinder to run low on brake fluid.i also assume that you are bleeding the brakes properly.Left front brake works with Right rear brake and Right front brake works with Left rear brake.this is how the brakes should be bleed.

Mar 15, 2011 | 1997 Buick LeSabre

1 Answer

Dell E177FPB monitor has ghost images "bleeding"


I had dual monitor with color bleed to the right. The solution was
1) identify optimal resolution for both monitors ( Dell 198wfp @ 1400 x 900) and (Laptop @ 1200 x 800) 2) check colour setting (32 bit or 16 bit) 3) reduce colour setting down to 16 bit) 4) Check performance 5) reduce screen resolution 6) check 7) cycle between screen color and screen resolution 8) if no luck, check updating the drivers for graphic card 9) if no luck, check updating monitor drivers 10) if no luck, check altering memory set aside for graphics (onboard memory for example or off-graphics-chip-on-RAM-memory) 11) Monitor checking software is very helpful : try "http://majorgeeks.com/download.php?id=22" for the Nokia Monitor Test (a CRT tester) or any other freeware/shareware testing program such as passmark's products etc.,
You might just have to suffer with a large workspace and mungy grapics performance though ... I am.

Nov 22, 2010 | Dell Computers & Internet

1 Answer

How do i change the fuel filters without bleeding


you cannot change filter without bleeding it you can however fill the fuel filter with injector cleaner that can be put into filter and NOT into the fuel tank this will help also u can get a external primer pump and attach to the OUT side of filter and pump the fuel through good luck

Jul 01, 2009 | 1990 Ford F350

1 Answer

Clutch master cylinder rebuilt, brand new clutch slave installed. Still can't get pressure to come up after bleeding on my 85 FJ1100. Original lines and seal on master cylinder cover. I'm at a loss here,...


Hi there,
Some times the clutch systems needs a vacuum
pump to bleed the system up to pressure. Also
note whilst bleeding the system don't let the reservoir run out of fluid. Also check if there is any other bleed nipples in this system. They all need bleeding.Hope this helps your problem.
Regrades Lighten



Apr 26, 2009 | 1985 Yamaha FJ 1100

1 Answer

Blows fuse


You may want to check the regulator IC. RCA had a lot of shorted regs

Nov 07, 2008 | Televison & Video

1 Answer

Red flaring


its called bleeding needs adjustment,call the tech that did the repair to adjust if it wasn't that long ago

Nov 10, 2007 | RCA F38310 38" TV

Not finding what you are looking for?
Sony KV-35S45 35" TV Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75846 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...