Question about Computers & Internet

1 Answer

Eurovoxex1000sl can anyone tell me which keys on my remote represents the letters to get update codes

Posted by on

  • archdeacon19 Nov 30, 2008

    thanx for email very helpful solved problem and box has got all channels now thanx agen

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 157 Answers

You need to connect your pc to your box via the rs32 null modem cable download the firmware for your box(its here in the d/load section)

open it then d/load to your box this is called flashing

then you just need to scan for channels set your area symbolrate first either 6.887 or 6.952 scan leave on sky sports 1 to update code then your away

Posted on Nov 30, 2008

  • Juli H.
    Juli H. Nov 30, 2008

    oopsies. ignore the previous comment. here we go..

    *************************************************************************************************
    HOW TO ENTER KEYS ON A EUROVOX RECEIVER
    *************************************************************************************************
    GOTO MENU PRESS OK ON CHANNEL SETTINGS THEN KEY 1968 TWICE
    THEN ENTER YOUR RIGHT KEY TILL YOU GET NAGRAVISION
    CHOOSE YOUR PROVIDER PRESS OK
    GO DOWN TO YOUR 00 KEY
    USE YOUR RIGHT LEFT KEY TO ENTER THE RIGHT ONE
    THEN PRESS OK TO GOTO THE NEX ONE
    SAVE ON EACH KEY (00 AND 01)

    OR

    PRESS MENU - THEN PRESS THE YELLOW TEXT BUTTON (BOTTOM RIGHT).

    PLEASE TAKE NOTE OF THE BELOW:
    TO ENTER LETTER A = PRESS TV
    TO ENTER LETTER B = PRESS RADIO
    TO ENTER LETTER C = PRESS P-
    TO ENTER LETTER D = PRESS P+
    TO ENTER LETTER E = PRESS INFO
    TO ENTER LETTER F = PRESS RECALL
    TO ENTER 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 = PRESS THE NUMBER BUTTONS ON THE REMOTE CONTROL.

    ENTER THE PROVIDER & KEYS FOR YOUR AREA & PRESS THE OK BUTTON ( press 4 secs ) TO SAVE. THIS WILL BRING THE CHANNELS BACK TEMPORARILY WHILST A NEW SOFTWARE IS BEING RELEASED.

    IF YOU ARE UNSURE WHAT AREA YOU ARE IN, JUST ENTER ALL 3 SETS OF KEYS ONE BY ONE.

    E.G. ENTER CW KEYS THEN PRESS OK TO SAVE, THEN ENTER THE NTL KEYS THEN PRESS OK( press 4 secs ) TO SAVE & FINALLY ENTER TW KEYS THEN PRESS OK TO SAVE.

    AFTER THIS HAS BEEN DONE, YOU SIMPLY EXIT OUT OF THE MENU & ALL THE CHANNELS WILL START WORKING AGAIN.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windows 7 can't activate on dell 14 r


That means you are using an illegal copy (one that has already been activated) or you typed in your Product Key Code wrong which is on the Certificate Of Authentication (COA) sticker affixed to the bottom of your laptop or inside the battery case. The COA will tell you which operating system you have and the series of 5 letters and numbers that represent your product key code.

Jun 03, 2012 | Computers & Internet

1 Answer

Code to unlock a kenwood dnx5140 car gps sterio


ype 1

  • During the code request mode, while pressing the DISP key, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
  • Enter the security code with the Kenwood remote.

Type 2

  • Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
  • Enter the security code with the Kenwood remote.

Type 3: Model# DPX-4020 and DPX-4030

  • Press and hold the 1 then the 6 preset keys until the display shows the letter C.
  • Enter the security code with the Kenwood remote.
Entering Letters with a Kenwood Remoteo enter a letter with a Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter. Press the Track Up or Next Track key to send the letter. To send the letter A, press the 2 key once then press the Track Up key. To send the letter B, press the 2 key twice then press the Track up key.
Finally, when all of the letters are entered, press and hold the Track Up button for 3 seconds.
The key sequence to enter the security code KCAR is:
  • 5
  • 5
  • Track Up
  • 2
  • 2
  • 2
  • Track Up
  • 2
  • Track Up
  • 7
  • 7
  • Track Up
The Kenwood should then enter tuner mode.
A Security Code Bug in Some Kenwoods

Oct 31, 2010 | Kenwood DNX5140 Car GPS Receiver

1 Answer

Witch year


The date of manufacture is determined by the SERIAL NUMBER. The following link explains how to determine the date code for a Maytag appliance:

http://www.fixya.com/support/r3576445-determining_the_age_of_your_maytag_appli

Look at the last two LETTERS in the serial number. The first letter represents the YEAR, the second letter represents the MONTH.

If you have any questions, please let me know. I hope this helps you.

Jan 14, 2010 | Maytag HYE3658AY Electric Dryer

1 Answer

I have a mp5028 and it tells me 2 enter the code.


you will need a remote for this
Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jul 05, 2009 | Kenwood 2005 KDC-MP5028 CD/MP3...

1 Answer

What do I do???


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

May 26, 2009 | Kenwood DDX6017 Car DVD Player

2 Answers

2001 Volvo S40 missing key/remote


You car has an integrated key and remote.

There is a software that needs to be downloaded to the car. When the remote is purchased at the dealer it comes in a plastic package. That plastic package has a sticker on it. The sticker contains id codes.

There are two codes one is 16 digits/letters and the second one is 8 digits/letters.

Without this sticker the dealership can not program the remote/key to the car. If you buy a key elsewhere, make sure it has the codes included.

Unfortunately you cannot program a remote yourself.

Apr 29, 2009 | 2001 Volvo S40

2 Answers

I have the codes, but how do i enter them into my eurovox box?


http://www.techwatch.co.uk/forums/44035-eurovox-frequently-asked-questions.html

I have a old erovox type 2 go into language type 1968 twice then selct what you provider it ok
I am trying to get the codes everyday anyone know the site

Dec 05, 2008 | StarTech.com StarView SV211K 2-port KVM...

1 Answer

Need eorovox codes 28 nov 2008


go to http://thechatterbox.cc and download the Chatterbox toolbar. Then Downloada program called KeyMaster on there.

Then on your remote, press MENU then the Yellow button.

Provider ID is as follows,
Before Virgin Media took over, type in what ever code is next to your old supplier..

NTL - 5401
TELEWEST - 5a01
C&W - 5c01

Use the key on the bottom of your screen to type in the Letters.

Nov 28, 2008 | StarTech.com StarView SV211K 2-port KVM...

1 Answer

Security code for kenwood kdcmp528


for your kdc-mp332 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Oct 31, 2008 | Kenwood KDC-MP528 CD Player

1 Answer

Kenwood KDCMP528


for your kdc-mp528 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Oct 29, 2008 | Kenwood KDC-MP528 CD Player

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18384 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...