Question about Jenn-Air JES9860 Electric Kitchen Range

1 Answer

Wont stop beeping

Hi,
i started to clean my microwave,accidently i touched the in built oven ,it startes beeping and is not stopping,its annoying,please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Try turning the breaker off for 5 min and reseting it

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oven beeps and displays F7. Hit stop/cancel, starts up again in about 10 seconds


Hi cpwdavis,

The F7 failure code shows a Function key shorted or stuck. To resolve this problem, you need to replace touch pad or if touch pad is part of the clock, replace the clock (ERC).

Hope it helps.

Thank you for using FixYa.

Sep 22, 2011 | Jenn-Air JES9800A Electric Kitchen Range

4 Answers

Was low temp roasting of ribs in Jenn Air JMW9530AAB convection oven. Heat webt ofand stove started to beep and displayed "-F7-". Cancel failed to do anything. Shut power off and when turned...


The electronic control may not be set correctly. If the control is not programmed correctly the oven will not start and you will usually hear a series of beeps instead of the microwave starting. See your Use & Care Guide

Aug 09, 2008 | Jenn-Air Kitchen Ranges

1 Answer

Self Cleaning NOT working and Locked itself...and BEEPS NON STOP


Hi,
Seems like you found out the hard way what I wrote about in this tip...
Check it out it also contains some thing to try on how to unlock that oven..

http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101
Asker's Testimonial " Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!! " - amymrocks


Asker's Testimonial " Thanks for this! I did not realize self-cleaning was so bad for the appliance2_bing.gif. Fortunately, I hardly ever do it! " - sej51

Apr 20, 2010 | Dacor ER36D Stainless Steel Island Trim...

1 Answer

F10 error on kenmore elite electric built in model 790.4907


Try unplugging the unit from the wall, wait 5 minutes and replug back in. I had same thing happen to me a few months ago. I had to leave my stove/oven unplugged for 24 hours to finally get it to reset itself. It is working fine now.

Aug 12, 2009 | Kitchen Ranges

1 Answer

The display at top of stove is showing "F1" and continuously beep


Maytag Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution F0 Function key stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F2 Oven temperature too hot Replace relay board, if present, or oven temperature sensor (RTD). Check sensor harness. F3
or
F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Watchdog and hardware conflict Replace clock (ERC). F7 Function key shorted or stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F8 Analog / Digital problem Replace clock (ERC). F9 Door latch Check door latch components.

Mar 19, 2009 | Maytag PGR5710 Performa Gas Kitchen Range

1 Answer

Frigidaire electric stove keeps beeping


IF IT HAS A MECHANICAL CLOCK, THE START AND STOP TIMES NEED TO BE SET, THE OVEN CONTROL SET TO CLEAN, AND THE SELECTOR SWITCH SET TO CLEAN.
TO CLEAN NOW SET START TIME TO THE TIME ON THE CLOCK AND THE STOP TIME TO 3 HOURS LATER.
LOCK THE DOOR. IT SHOULD START AND THE CLEAN LIGHT SHOULD ILLUMINATE, OR OVEN ON LAMP SHOULD LIGHT.
IF IT STILL DOESN'T WORK, THERE IS A PROBLEM WITH THE CLOCK OR THE CONTROLS OR THE LOCK ASSEMBLY.
A WIRING DIAGRAM WOULD BE BEST FOR DIAGNOSING THE PROBLEM.

Feb 20, 2008 | Frigidaire FEF336BC Electric Kitchen Range

1 Answer

F1 error code, continual beeping all other oven functions work properly


Here are the error codes for Dacor:

DACOR
Range/Stove/Oven Fault Codes Failure
Code
Condition Check/Repair F0 Clock pushbutton is stuck in a depressed position Check clock buttons F1 Element relay circuit failure Control board may be bad F2 Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only) Call for service F3 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F4 Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace F6 Failure in the EEPROM check comparison (only time of day and timer will operate) Call for service, electronic clock control is usually the cause of the problem F7 Failure of the self- clean automatic door latch system Check door latch and switch(es) F8 Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean mode Check door lock motor and door latch

Nov 08, 2007 | Dacor Epicure ERD30 Dual Fuel (Electric...

Not finding what you are looking for?
Jenn-Air JES9860 Electric Kitchen Range Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Kitchen Ranges Experts

Mike Carew

Level 3 Expert

958 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Jenn-Air Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...