Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Model LSQ8543JQO The cold water fills very slowly and the warm water works fine. I checked the hoses and they are not kinked and both water spickets are on completely.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Remove the cold water hose at the unit and look in the hole where the hose conects if the screen is clean then the valve is bad if it it cloged clean it

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacement of cold water valve on ge model wpgt9360eoww washer


Is this a new development or has it always done it slowly? Before jumping to parts changing, make sure it isn't something simple like a kinked or obstructed hose or even something like someone nearly closed the supply valve!

Dec 02, 2014 | GE Washing Machines

2 Answers

Water for intial fill works fine . when it goes to rinse cycle the water just dribbles in making wash time go on for ever ! whats the solution?


when you start the washer set it just on cold and see if it fills slowly,when the washer goes to rinse it just uses cold water,you could have a problem with the washer or in the house,when you run it on just cold and if it dribbles in,stop it shut down the water going to the washer,remove the cold water hose from the back of the washer,stick it in the sink or inside the washer and turn it on,if it comes out strong then you have a bad water valve on the washer,if it comes out slowly you have a bad water valve in the house and it's not the washer.hope this helps

Sep 12, 2011 | Washing Machines

1 Answer

My washer will fill with water during the wash cycle just fine, but during the rinse cycle the water just trickles in. The water lines seem to be fine. What else could be causing my problem?


usually the wash is a mix of hot and cold and the rinse is just cold, that said, it is most likely a problem with the cold water supply. check to make sure the cold water valve is all the way open and the hose isn't kinked. If those are ok turn the water supply off and remove the supply lines on the machine side, you will see a screen inside the washer that may be clogged with sediment. If so, just clean it out and put it back together. You may also want to run a wash cycle on cold only to see if it fills slowly for the wash cycle. If it does fill slowly on cold you have low pressure on the cold side.

Jan 07, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Hot water fills very slow(30 MIN OR MORE TO FILL) good water flow from spicket to washer, screens are clear. sewems to be something with the washer its self


Might be a bad inlet valve. To confirm, swap the hot and cold hoses to your washer so that the cold water feeds the hot water connection and the hot water feeds the cold water connection. Turn off both hot and cold water faucets. Set the washer for a warm water wash. Turn on the cold water faucet, and check the flow. Then turn off the cold water faucet, and turn on the hot water faucet and check the flow. If the cold water flow fill slowly, then the problem is with the inlet valve.

It an easy part to obtain from an appliance supply house. To install disconnect the hoses to the back of the machine, and remove the back panel to get access to the valve. Should only take a couple of minutes to remove and install. Hope this helps you.

Oct 26, 2010 | Kenmore 24032\24036 Top Load Washer

2 Answers

My GWL10 fills really slowly. It starts fine with the hot water, then slows to a trickle when it switches to cold but it doesn't seem to affect it if I change the temperature selection. I normally leave it...


sounds like you have a restriction on the cold water water pipe kinked or a blockage turn off cold water and remove pipe from cold tap then turn tap on and see if water is coming through fast enough if it is then the restriction is in the hose or valve on washing machine if not then the restriction is in the cold water tap

Jul 14, 2009 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Not hot water EF0 code


Check for kinked or blocked
incoming water hoses, clean the incoming
water screens. If problem still remains,
replace the water inlet valve assembly

May 16, 2009 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

Model 530 Frontloader - No water


IS YOUR DOOR FULLY CLOSED TRY PUSHING IT IN

May 14, 2009 | Frigidaire Washing Machines

1 Answer

Whirlpool Top Loading Washer not filling when set on hot only


check the water inlet valve assembly. Also, this could be a timer issue as well. check the Hot valve block connector on the control panel board. it could be lose or separated or broken. there is a wire that leads to the valve on the hot side as well. check this.

Mar 13, 2009 | Washing Machines

1 Answer

Water inlet


Have you checked the little mesh filter that may be in the hose? Sometimes sediment and other debris can build up causing slow filling. Turn the water valve fully off. Remove the hose from the valve and the machine. Check for a mesh screen in both ends of the hose, possibly even in the inlet to the machine. Remove and clean. You could also have a kink in the hose, bad hose (seen this too many times, just swap the hot and cold and see if the problem moves) bad solonoid valve, bad supply valve, etc.

Jan 04, 2009 | Frigidaire Washing Machines

1 Answer

Slow rinse cycle fill


take the hose off the cold water valve and check the screen on the water valve ,make sure the cold water is on all the way and the hoses are on the right valves get a water bucket hold the cold water line in it open the cold water valve to check the pressure

Jan 30, 2008 | Kenmore 98702 Stacked Washer/Dryer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...