Question about Galaxy Radios DX-99V 40-Channels Base CB Radio

1 Answer

I got a dx99v cb it turns on but its not transmitting or receiveing the needle barely moves.

Posted by on

  • Anonymous Feb 10, 2009

    my galaxy dx-99v does not transmit

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 211 Answers

You may have a bad regulator transistor.
Good Luck on this problem, and I hope this has helped.
Ed Meshechek ( Radio Man )
NC Electronics
PO Box 1696
414 6th St
Mills, Wyoming
82644
307-266-4675
wyoed1@aol.com

Posted on Dec 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cobra 29ltd turns on but no sound afterwards, not even when I ask for a question the needle doesn't move after I ask the question, installed in a freightliner cascadia


I guess i will have to ask you the most obvious things. Do you have a suitable antenna connected? The needle moves on receive in most cases, not transmit. A watt meter will help you know if you are transmitting.

Aug 21, 2016 | Cobra Radio Communications

1 Answer

NEEDLE MOVES ON RECIEVE LIGHT BURNT OUT AND NEEDLE DOES NOT MOVE ON TRANSMIT IN S/RF,SWR OR CALIBRATE BUT RADIO TRANSMITS GREAT..


try blowing some canned air on the knob and switch to remove dust , also try a dash of electrical component spray on them , then see if it works.

May 06, 2015 | Cobra 29 WX NW ST 40-Channels Base CB...

2 Answers

Receives fine, needle does not move on transmit, transmit light lights


Needle on the meter might have went out . Is it stuck in one spot? If it moves during receive and goes to zero when keyed it most likely the final.

Mar 08, 2015 | Radio Communications

1 Answer

What does it mean when the needle moves with the beat of the radio?


Either your power supply is struggling to deliver enough current so when the speaker volume increases, the remaining power for the receiver decreases or the person transmitting has an over modulation problem.
If you turn your volume down and the needle stops bouncing, you may need to look at your power connections or have your radio serviced and set back up.

Mar 04, 2014 | Radio Communications

1 Answer

Will a diesel 360-3 mic ork on a galaxy dx99v



  • Hi, I can help.

  • The Diesel Electronics CB will work but you have to wire it as stated below.

  1. #1 Shield and Black - Ground
  2. #2 Yellow - Audio
  3. #3 White - Transmit
  4. #4 Red - Receive

  • I don't know if anyone before you has re-pined that mic or not so if you just remove that little Philips screw at the mic connector and then give it a quarter turn you can slide the connector out and take a look and compare the wiring. The actual numbering for the pins on the Galaxy 4 pin mic connector is as indicated below in the diagram. As you look at the mic tip make sure the indent on the mic is as it is the diagram.
ironfist109_269.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Sep 22, 2011 | Galaxy Radios DX-99V 40-Channels Base CB...

1 Answer

I can transmit but sometimes it won't receive. I put on a new cable today & and a new ant. last week (classic 29)


Watch your meter and if the needle is moving but you can't hear anyone then try a different microphone. The wire for receive might be broken intermittently.

Jun 15, 2010 | Cobra 29 LTD CB Radio

1 Answer

My galaxy 959 sqeals and does not receive or


mike has wiring problems. Check for breaks in cord and where the plug goes into the unit. If not original mike then has incorrect wiring for the radio and will need to be changed for config

May 01, 2010 | Galaxy Radios DX-959 40-Channels Base CB...

3 Answers

Galaxy dx99v cb radio


did this problem occur while radio was being operated? or when it was being worked on? or a result of being worked on?

Dec 04, 2007 | Galaxy Radios DX- 88HL Base CB Radio

Not finding what you are looking for?
Galaxy Radios DX-99V 40-Channels Base CB Radio Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Galaxy Radios Radio Communications Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Brad Brown

Level 3 Expert

13804 Answers

Mike Charette

Level 3 Expert

1769 Answers

Are you a Galaxy Radios Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...