Question about Marantz SR-7200 Receiver

1 Answer

OSD control from receiver

How do I get the OSD to work on the AV 7200? Is it controlled from the remote only or can I directly work it from the receiver? Will the display show up on my TV or on the remote screen?

Posted by on

  • Cadal Dec 09, 2008

    The controller provided from Marantz is as close to the SR7200 model, however since they no longer make the 7200 they could not provide a better one. So I need to know if it is possible to open the osd from the receiver.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

I had the same problem on my 7200 until I realized that the display comes up on the television screen. I carefully followed the set up required from the manual. I got the Manual online at Marantz.com. I have a cable hook up so I connected the video cable out from the box to the Video in source on the 7200 and monitor out to my Television. I then pressed the Amp button to get the remote to Amp mode. I then pressed the OK button that is in the center of the four direction buttons and the menu displayed itself on the screen . I hope this helps. ercble

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't access osd on screen display from remote control


Have you checked to make sure your TV is on the correct input?

It should be on the input the Receiver is connected to in order for the OSD to appear .

Sep 30, 2014 | Harman Kardon AVR 135 Receiver

3 Answers

Yamaha RX-V1000 volume control erratic, remote doesn't work. All was well then the volume control knob became erratic (volume would change erratically as knob was turned in either direction, remain...


sounds like you need to take it in to have it looked at. no simple fix unless you are an appliance technician. hard to walk a beginner through. i suggest calling an stereo repair guy.

Fix Ya
FixYa Support

Please accept solution and rate 4 thumbs up! Thanks for your feedback!

Aug 21, 2011 | Yamaha RX-V1000 Receiver

1 Answer

My volume control on my Aiwa surround sound system no longer responds to my remote controller. Everything else works fine using the controller


Assuming the physical volume control on the receiver still works I would say the remote's volume control is faulty.

Read this procedure to possibly fix the remote:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12963989782821
They also sell replacement remotes.

Zoom in on the picture of the original remote provided on the site (or look at your own) and get the actual remote model number.

or check eBay: search for "(model of the device or the remote) remotes", check the 'include description' box. Usually cheaper than the vendors.

Jul 20, 2011 | Aiwa AV-D58 Receiver

1 Answer

Remote controller for Nakamichi AV 10 amp. stopped working last night despite replacing new batteries. Red LED not illuminating when 'power' button depressed. Any suggestions for repair/replacent of...


Hi,

I got the Nakamichi Av-10 i too face the same problem i just tap the remote with my palm and it starts working...:) just try this am sure it should work

Jan 07, 2011 | Nakamichi AV-10 Receiver

3 Answers

I used to get OSD on the TV with my receiver, but it has gone and I don't know what setting to do to get it back. It is a Pioneer VSX-917V-s/-K. Thanks


did you happen to change to cable connecting the Reciever to the TV to an HDMI?

please note that the OSD will not appear if you have connected using the HDMI output to your TV.
Use component, S-video or composite connections for system setup.

Dec 30, 2009 | Pioneer VSX-917V-K Receiver

1 Answer

What's NEC PF68S33 TV's remote control code for YAMAHA HTR-6130


I had similar problem when setting up the YAMAHA remote control for my NEC LCD TV. At the end I found I did not follow the YAMAHA manual properly. Did you hold down the DTV/CBL button, and AT THE SAME TIME press the AV POWER for 3+ seconds? You should be able to "REMOTE SETUP OK" displayed in the front panel of the YAMAHA AV receiver. Hope this helps. BTW, only the TV POWER, TV MUTE and the numeric buttons work in my case.

Dec 30, 2008 | Yamaha HTR-6130 Receiver

1 Answer

My OSD does not come on


Try plugging a video rca cable into the "monitor" on the back of the mixer (second down or something like that) and then to your tv. This pumps the osd signal to the tv where you can manipulate the menu options.

Think this analogy:
remote = keyboard
receiver = computer
tv = monitor

You need a connection ultimately to the tv for the osd to work.

Aug 12, 2008 | Marantz SR-7200 Receiver

1 Answer

Marantz sr-7200 no OSD


Press AMP then OK on your remote. If the menue does not appear press 9 on the remote. You must have your monitor connected through composit Monitor Out or S-VHS.
Also check your multiroom settings. Maybe your OSD signal is diverted through to other room. I do not have SR-7200 any more, unfortunately.

Jul 24, 2008 | Marantz SR-7200 Receiver

1 Answer

Brand Code


Which Universal Remote Control do you have?

Sep 26, 2007 | Aiwa AV-NW50 Receiver

Not finding what you are looking for?
Marantz SR-7200 Receiver Logo

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marantz Audio & Video Receivers Experts

gaucherre

Level 2 Expert

180 Answers

Pieter Vleeshouwers

Level 3 Expert

1410 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Marantz Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...