Question about Televison & Video

Open Question

Hi Hi I have the Eurovox 2007 and over the last few days its been showing 'please wait code being updated' each time this happened I switched off at wall and then restarted, put the channel to sport III then after few minutes it worked. Until last night, then couldnt get rid of message, tried the same this morning. Contacted Bubble cables they gave me some new codes. NTL 54 01 62 bd 22 0a c6 86 9c 93 80 ad d1 d3 80 90 ff 2b all the above has not worked. Do you have any advice to help me please Regards Sue Summers email is suesummers1310@yahoo.com Thankx

Posted by on

5 Suggested Answers

techman
  • 3130 Answers

SOURCE: toshiba 42wt29b. screen keeps turning blue

MMMM Hard call here. The fact that it does try to come on blue maybe an indication that the power supply regulator circuit is good. It could also be a shorted blue tube and when it comes on its overloading the screen drive and the set goes into overload protection shutdown. The real way to see Would be to pull off the blue crt socket as well as the Hi Voltage lead on the crt and see if the set comes on without blue. If it does Your gonna need a pict tube. If it dosent then troubleshooting along the switched power supplys would be neccassary.. BUT I advise you THAT IF YOU HAVE NO EXPERIENCE TROUBLESHOOTING TV SETS PLEASE SEEK A PRO TO ASSIST YOU AS THERES VERY HIGH VOLTAGE INSIDE THESE SETS EVEN IF THEY ARE UNPLUGGED. GOOD LUCK

Posted on Jun 29, 2006

  • 1153 Answers

SOURCE: Mitsubishi mod WS55511, 55" platinum series, power and code problem

Press the menu button for 10 sec on the set

Posted on Mar 24, 2008

  • 184 Answers

SOURCE: Toshiba 56hm66 New lamp worked last night, wont boot up again

You now have a defective lamp ballast board. It sometimes is the root cause of lamp failures in these sets. The problem here is that Toshiba does not sell the ballast board independently from the larger, more expensive light engine assy. Call Best Buy back and get a servicer out there. He may have to take the ballast board out of your TV and send it out for rebuilding.

michtech

Posted on Feb 14, 2009

  • 139 Answers

SOURCE: Samsung HL-S5086W Television. 3 yr old. Never

Hello,
Dont worry, the problem is coincidental to you installing the Wii. You need a new lamp.
What you are seeing is the lamp ballast/power supply attempting to start and restart your lamp. The resistance of your lamp to it's power source has increased to the point that it is shutting down, but has not blown out yet. You can find these at justlamps.com
Good luck

Posted on Jan 04, 2010

  • 1 Answer

SOURCE: My Ant A Input Not Working

After power outage, had similar issue. Simply set AV NETWORK to "OFF" and "TV LOCKED TO INPUT 1" to "NO". Worked wonderfully. Thanks a lot.

Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Black screen, blinking green light, nothing happens


Hi it is the indication of error code......can you tell me how much time does light blinks......

Jun 03, 2009 | Mitsubishi WD-52528 52" Television

Tip

Hello I read ur answer to the Fl 231 fuse problem in rca projection tvs. I have...


FL231. FUSE.... The RCA ITC222 chasis has a common problem. and it not all that difficult to repair. Does your rca projection tv have read blue and green shadows? Does it have bowing in affect on the top and bottom of picture? when you turn it on does some thin red green and blue line bow in from the top then go away. The main question to determine if you have the fl231 fuse problem is if you go into customer menu then setup do you have the "CONVERGENCE' option. If you do not. then i suspect you have this problem. In the manufactering of these sets Lead free solder is used. now there is great debate over the use of lead free. connection tend to be more brittle. cracks develop around the solder connections of the high voltage flyback transformer. this very small crack set up oscillations in the cuicit with a 400 milliamp fuse. THis fuse cant take it. When this fuse blows the processor then does not know its a projection tv with three projection tubes. it thinks its a crt tube tv. and crt tube tv dont need "convergence" so it removes the convergence from the set.

TO REPAIR... 1. Warning. this set can generate leathal dangerous voltages even unplug do not attempt if you have no experence with electronics.
2. Remove the back. there a number of torx 20 screws.
3. what you will see is a number of circit boards There will be one on the right and one on the left. the one on the right is the small signal board. the one on the left is called the power deflection board. it has a large black part with a big red or black wire coming from the top, this is the flyback.Next to the flyback on the right of it there will be three small rectangular componets tan or brown in color. these are fuses. the one in the middle is the fl231 fuse.
4. getting to this fuse can be difficult. these two cuicit boards sit on a tray that is removable. to remove this tray it is pulled out and up. BUt watch the wires.loosen the wire tyes.
5 when you get the tray up the bottom side of the board can be accessed
you will now have to unsolder that fuse. one side of this fuse is under a plastic part of the tray. i have found the easest way is to cut away the plastic to get to it. if you dont want to do this you will have to remove the board. only remove half of the plastic brace
6. REPLACE FUSE RCA PART 259213
7 RESOLDER FLYBACK CONNECTIONS simply heat up and add a little solder
8 reassemble set. make sure you examine the set for loose connections.
9 and remember "BE Careful'

on Feb 19, 2009 | RCA R52WH73 Projection Television

1 Answer

I have A Pioneer SDT50W1 rear projection TV which is about 11 years old. It is in A1 condition but recently I have had a problem when turning on the set. When I press the on off switch on the front of the...


The most likey cause of this is poor solder connections either in the power suply area or the convergence circuit area. If you can solder and are comfortable working inside the set where there are potetially dangerous high voltages (even when unplugged), you maight be able to resolve this yourself. Try resoldering any connections on the boards that appear grainy or have rings. Update this with your results.

Thanks,
Dan

Feb 18, 2009 | Pioneer Televison & Video

1 Answer

How to input eurovox codes


press menu whilst on the channel that says updating codes please wait. then press yellow key.. this will bring up a screen with nagra on it...

use the keys as they state on the bottom of that screen and input the code all using the remote...

Nov 30, 2008 | Televison & Video

1 Answer

Code for eurovox max v


Leave it a few days, they are changing every day and in every region. It will settle down in a week or so and software fixes will be around by then.

Nov 30, 2008 | Televison & Video

1 Answer

Eurovox searching for updates


press menu then yellow you then need to type in the following letters and numbers
press menu then the yellow button then type in the following
5a 01
98 b0 ba 52 d3 21 08 b4
d2 ea 29 b7 b5 52 e9 ad
then press ok then exit

Nov 30, 2008 | Televison & Video

1 Answer

Eurovox v


yes you could be right thats the info ive been getting as well judt wait few days then if still no luck then the chances are youll need the new download thats if you can get it as im not sure how virgin are doing it now i know ntl was no problem but since virgin took over things seem to have been changed causing problems with the older boxex.
Did you use a download originally or was it all ready done.

Any way sorry i couldnt give you a quick fix but it looks like its out of our control
Let me know how you get on over next few days you never know it might just come back on could just be downtime.
Have you gone onto virgin medias website and looked on their as it tells you what areas are having problems and what are having down time it might be worth a look

Apr 10, 2008 | Televison & Video

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69718 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6364 Answers

yadayada
yadayada

Level 3 Expert

63572 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...